Question about 2005 Honda VTR 1000 SP-2 (RC51)

Open Question

The F1 light comes on on the dash when accelerating hared wich cuts power for aprox 1 second. Intermitantly.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PDP-4340HD keeps turning off.


Continuous blinks of standby light indicates a fault in the IIC data bus. The main board is likely to be faulty. If you wish to know more Check this link.

Feb 03, 2013 | Pioneer PureVision PDP-4340HD 43 in....

2 Answers

Holden captiva is lacking in power, check engine light comes on and traction control lights come on and decline ascent light on dash shortly followed by service light and a large clunk sound. The motor...


I got a same problem in Holden Captiva diesel 2010 model as soon as you accelerate on traffic light the traction control light comes on engine light on dash, engine lack of power, turn the engne off for few seconds and goes ok but engine light stays on dash. Checked with the tech tool, it comes fuel metering code, can bus code... What it could be????. I've already changed fuel filter and did general service, still comes on. ANY IDEA PLEASE. OR I BURN THIS CRAPTIVA

Oct 13, 2011 | Cars & Trucks

1 Answer

F1E1 error happened repeatedly, jenn air says cut




F1 - E1
EEPROM checksum error
1.
Disconnect power for at least 30 seconds.
2. Re-apply power and observe for
at least one minute.
3. If code re-appears, replace control board (also
called ERC or clock).

Note: Applies to all F1-E...
codes except F1-E3.

Read more: http://www.appliancepartspros.com/repairtips/repairtips_appliance+fault+codes.aspx#Jenn
Air Range / Stove / Oven Fault Codes#ixzz19GMNtS3r


http://www.appliancepartspros.com

Dec 24, 2010 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

Cleaning oven got a warning beep and an F1 indicator in light panel


F1 error code normally means the oven temperature has exceeded the safe limit for the oven and the beep is to warn you to switch off until it has cooled down.

Normally this is caused by failure of the oven temperature control sensor which then fails to cut off the power to the heating element as it should.

Sometimes it is just a 'glitch' wich can be solved by turning off the power to the oven for a few minutes and then turning back on but if the problem persists you will need to replace the sensor.

Jan 12, 2010 | Jenn-Air Ovens

2 Answers

Start button does not work on our Asko t720 dryer


if you get a light on the main power switch, then it might be overheat cut-off switch wich has been activated. This is located outside on the back of the machine. a rubber button aprox in the middle, you must push this, and hear a 'click'. it might be a solution.

Jul 07, 2009 | Asko Dryers

2 Answers

After a power outage oven will no longer work


F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.
Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
$$$$

Apr 02, 2009 | Whirlpool 30" Self-Cleaning Freestanding...

1 Answer

My truck is cutting out. please help


your problem is your fuel pump ,,replace filter and test pressure gm trucks are know for it it will do this intermitantly then finally just quit on you

Dec 30, 2008 | 1993 Chevrolet C1500

1 Answer

Wolf built-in Wall Oven 762. Convection Fans stop turning intermitantly Oven shut down with F1 warning Later restarted ? meaning of F1 warning


How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.
  1. Disconnect power to stove
  2. Gain access to the back of the clock (electronic range control or ERC).
  3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
  4. Make sure everything is clear and will not short out when power is turned back on.
  5. Turn power back on to stove.
  6. Watch for the F1 and listen for the beep.
  7. If you get the F1 and beep, replace the ERC.
  8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.
http://www.applianceaid.com/fault_codes.html
click the link

Dec 06, 2008 | Kitchen Ranges

Not finding what you are looking for?
2005 Honda VTR 1000 SP-2 (RC51) Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...