Question about 1998 Honda CBR 250 RR

2 Answers

Hi, I took my speedo and rev counters of my '99 Fireblade appart to fit new backgrounds but now my MPH and RPM counters are showing the wrong readings. i managed to get them very close to the correct readi ngbut they still not as they use to be. How do I reset or get them back to normal? Thanks

Posted by on

  • francois_hym May 30, 2010

    HI I took my speedo and rev counters appart (Fireblade 1999) to install new backgrounds but they showing the wrong readings, how do I reset them again?
    Cheers

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,427 Answers

Ok,, in the cabl of the meter is a sprint type lever that moves to show u the reading..
its mounted on an electro magnet coil,, there should be a screw there that can adjust ,, adjuct them both to 0,, if not there look at the lever ,, to the buttom u will see a pring lock pin that the lever hits on,, bend it a bit to get them to 0,,

thats it..

Posted on May 30, 2010

  • francois_hym May 30, 2010

    I had a llok but my speedo doesnt have a cable, it has a multi pin plug at the back of the speedo and then a wire with a sensor that goes into the engin. Looked in my Haynes manual and there's no mention of a speedo cable ether.

    Rhanks

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi! Just a tip bout the issue. This bike's counters needs to be calibrated and most fix on this can be provided by the dealer for they have the tools and device to do this. HOpe this helps and have a good one!

Posted on May 30, 2010

  • dj_relly999
    dj_relly999 May 31, 2010

    Good luck on this. Have a good one!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Triumph twin, the rev counter has started to read below the real rpm. The faster the revs the more wrong is the tacho


The inner part of the cable could be slipping / warn out or broken.
Check the cable where it attaches at both ends, tighten up if loose.
Take the cable off and check the ends for obvious wearing, if the inner cable looks damaged, replace with a new one.
Hope this helps.
Some bikes have a totally different set up to how they read the rpm
you could try a after market rev counter, good luck

Feb 06, 2014 | 1999 Suzuki GSX-R 600

1 Answer

Fireblade speedo


Hi, Anonymous you have a connection issue between the power source and the speedometer, you need to run diagnostics the next time it does not function properly, for more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.fireblades.org/forums/electronics/91020-cbr-929rr-speedometer-not-working.html
Speedo not working
2004 2005 Honda CBR1000RR Fireblade Service Manual Moto Data Project
http://www.partsfish.com/page/oem-parts-for-honda
Honda CBR1000RR Fireblade Owner Manual

Jun 06, 2017 | Honda CBR 1000 RR Fireblade Motorcycles

1 Answer

Speedo and rev counter reading even when engine is off!


I have a similar problems on my 2005 9-3. It has developed a number of minor electical issues. including dial and false warning light triggers. I have fixed most of them by simply going round the car disconnecting the electical connectors and spraying "switch cleaner" (Maplin or Radio Shack).
The only problem I have left is the rev counter occasionally starts reading high, removing the fuse (end of dash panel - 4th fuse down) for about 30s with engine off normally resets everything back to normal.
Hope that helps.

Feb 09, 2013 | 2006 Saab 9-3

1 Answer

03 mitsubishi endeavor engine cuts out at 4000 rpm when driving revs fine when in neutral. It has no engine codes. any ideals?


At 4000 rpm what does your speedo say. Your computer may be limiting both your mph and your rpms. I have a 2004 Ford Ranger at 90 mph the engine sputters and seems to miss. It will stay at 90. In neutral it revs fine. My problem is because of chip programming in the computer. Your problem may be the same.

Aug 08, 2012 | Cars & Trucks

1 Answer

Instruments not working on benelli trek


sounds like one of your display fusers gone or a loose connection

May 15, 2012 | Benelli Tre-K 1130 Motorcycles

1 Answer

1998 Honda Fireblade CBR 900 RR won't rev past 6500 RPM


Hi, Gingerteddyb for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.fireblades.org/forums/honda-fireblade/80184-rev-limit-cbr900.html
bike will not rev past 8k like hitting the rev limiter
Honda CBR900RR Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CBR900RR Fire Blade Owner Manual

Aug 15, 2010 | 1998 Honda CBR 900 RR Fireblade

1 Answer

Hi, i have a 95 golf 1.9 td and my cluster work exept the speedometer and the rpm, any solution????


try a new speedo drive in the gearbox and the rev counter works from a sensor mounted on the flywheel as i remember

Jun 12, 2010 | 1995 Volkswagen Jetta

2 Answers

Engine warning light , battery light, warning light , rev counter , speedo and temp gauge going on/off intermitantly and speedo not working on digital screen on ford focus can you help. the battery is new...


My 04 Ford Focus the battery light keeps coming on & going off, have fitted a new alternator belt but it didn't solve the problem. The battery connections are good. Also the rev counter, speedo & mileage clock keep going haywire when the battery light is on. Do you think it is the alternator? Or is it some other common problem?

Jan 21, 2010 | 2003 Ford Focus

1 Answer

Fireblade 929 on a y plate .. speedo and rev counter just stopped working any idea


Sounds like a wiring/connector problem. Could be the common earth connection that has corroded. Check all wires that go to BOTH the rev counter and the speedo, since both went out at the same time.

Jun 06, 2009 | 2001 Honda CBR 929 RR Fireblade

Not finding what you are looking for?
1998 Honda CBR 250 RR Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...