Question about 2000 Honda Cityfly

Open Question

Fork oil my 2000 model cityfly has to have new seals put in and the shocks now have no iol in them, how do i put more in. thank you for your time

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

robotek
  • 1512 Answers

SOURCE: Front fork oil capacity

Hi Lukepentcof.

its 350cc or 11.8 ounces in the Clyma book, but that's for a 1986 onwards model. you can vary the amount you use to suit your style of riding anyways. I doubt it would be that far from the mark.

regards
robotek

Posted on Dec 08, 2008

  • 6 Answers

SOURCE: front fork leaking oil from bottom of the seal.

This is one of the few things that I recommend you take to a shop - you need some very special tools and techniques to fix this problem. Sorry,
Kevin

Posted on Dec 30, 2008

  • 74 Answers

SOURCE: Fork oil level: 2006 KDX 200

This all depends on what size forks you have, but a good rule of thumb is 120ml. After that then what you want to do is to ride the bike and make adjustments to your front end until your liking.

Posted on Jan 16, 2009

cape cod bob
  • 292 Answers

SOURCE: Need to change fork seals on xr400

http://www.carlsalter.com/motorcycle-manuals.asp

free pdf service manual here

Posted on Apr 03, 2009

  • 3567 Answers

SOURCE: i need to know the fork oil level for a yzf250

Factory service manual says 19 ounces > Manual Page 2-12

You can download a free PDF of a factory service manual at this web site >
http://www.carlsalter.com/motorcycle-manuals.asp

Please rate this answer. Four diamonds would be nice. Thanks!

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 flstc , just replaced the " fork seals ", still leaking on left side. i was told to replace " oil seals " under the " slide tube cap " and spacer. will this...


Well, yes. The fork seals are located at the top of the fork slider un the "slide tube cap". This makes me wonder exactly what did you replace when you say that you just replaced the "fork seals". To get to these oil seals, you have to disassemble the forks tubes. Remove the front wheel and fenders. Down where you took the axle out, look up into the end of the slider and you'll see a socket head bolt, 6mm. Loosen this bolt before you take the tube out of the triple tree. Remove and repair one tube at the time. When you get the slider off the top tube, you will see a retainer ring in the top of the slider. The seal is under this ring. The new oil seals must be replace squarely in the tube. When you reassemble the tube and put it back in the triple tree, there is a specific amount of fork oil that must be added to each tube to properly refill it. You must use the "dry" quantity when refilling the fork tube because you disassembled and completely drained the tube. I'm sorry but I don't have this quantity of fork oil for this late of a model bike. I work on the earlier model bikes only.

good luck
steve

Jul 19, 2011 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

How much fork oil is required in the front forks of a 2000 suzuki 800 intruder and how do you measure if you put too much in. The guy at cycle gear where I bought the fork oil said to top it off or fill...


Hi, all model VS 800 from1992-2000 take the same amount of oil in the front forks, using 10 weight fork oil measure into a clean measuring device or mark the side of the oil bottle 413 mls, pour this caerfully into 1 fork, and the same amount into the other fork, 413/413 cm (3)

May 09, 2011 | 2000 Suzuki VS 800 Intruder

1 Answer

Xr 200 fork problem


no air required. the air valve on top is to release pressure after heavy pumping. ie motorcross... check seals. you can run a feala gauge inside seal to clean dirt out or replace if worn. put in correct amount of oil an off you go....

Jun 30, 2010 | 2002 Honda XR 200

2 Answers

How much Oil does a 2005 Honda Shadow Spirit take?


Hi
The oil capacity on the Honda Spirit is 3.3 qts

Thank you

May 16, 2010 | 2005 Honda VT 750 DC Shadow Spirit

1 Answer

My forks are leaking iol


They need fixing, take it to a reputable cycle workshop and get them to assess it.

Dec 27, 2009 | 1996 Suzuki GSF 250 Bandit

1 Answer

Seals blown on front shocks


to remove seals you will need to remove each fork leg from the bike,i put the bike on the centre stand and jack under the motor to get the front wheel off the ground,after you remove the fork leg,remove the dust cover(if fitted),remove the circlip holding the old seal,you may have to stab through the old seal with a screwdriver to remove the seal from inside the leg(be carefull not to damage the chrome on the fork leg),clean around the surfaces and install the new seal making sure it goes back in dead square,refit the circlip,then refit the dust cover,replace fork tube back in bike and top up with new oil,most bikes take between 300 to 500cc of oil,but check with your local shop as all bikes are different,and you can adjust the amount of rebound damping by varying the amount of oil you put back in,..sounds complicated but quite an easy job..hope this helps

Jul 04, 2009 | 1995 Suzuki GS 500 E

1 Answer

Hi my name is Andy i have a GS550 cafe racer the falk seals are leeking how much iol do you need per leg? andy.williams@hotmail.co.uk


you should put in new fork seals before adding oil -leaking fork seals should be repaired as oil can get on the front brake pads--buy a clymer manual and you can change them yourself

Jun 26, 2009 | 1983 Suzuki Gs 550 L

2 Answers

How to fill the front suspension on a ktm exc 2001


If you get the sevice manual or contact a dealer to get the correct oil amount for your bike, they need to know the model and year, you have to have the forks off the bike. take the fork caps off, take the springs out compress the upper fork tube all the way and add the specified oil. if they also give you the measured amount from the top that's the best way to get both fork oil levels exact. there is a special tool that you set the oil level in millimeters and it sucks out the oil to the right level, but before you do that step after adding the oil always pull and push on the cartage rod several times to remove air from the cartage tube. you will hear the air coming out and you will feel the changes in the cartage rod as the cartage tube fills up with oil and the air is removed.
something i'm confussed on though is if you replaced a seal you would have had to brake down the fork to replace it. you would have poored the oil into a container, cleaned all the internal parts,and used a fork seal driver to install the new seal. part of your question asks where do i put the oil in? thats in the open end of the fork after you have taken off the fork cap. It sounds to me like you only replaced the dust seal on one fork. that is not going to fix your leaking fork. you need to replace the oil seal thats pressed inside of the top fork tube.

Dec 01, 2008 | 2008 KTM 200 EXC

Not finding what you are looking for?
2000 Honda Cityfly Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...