Question about 2001 Kymco Stryker 125

1 Answer

Need to know the diamiter of the air intake of a 98 kymco sector i want to fit a k@n air rilter but dont know the diamiter of it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 832 Answers

If you remove the pipe to the air filter box you can measure it, but if you fit a K&N filter you will have to re-jet the carb, or it will not run properly

Posted on May 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kymco 300 mxu when back fires


back firing is usually a sign of an air leak on the intake manifold.

Dec 01, 2016 | Kymco 2008 MXU 300

1 Answer

My 50cc kymco scooter starts but when you pull the throttle back it cuts out


Hi, Christopher and the usual suspects are:
1. Idle circuit and transfer ports clogged.
2. Air fuel mixture adjustment too lean.
3. Pilot jet clogged.
4. Faulty accelerator pump.
5. Float level too low.
6. Float bowl contaminated old fuel, water, dirt, rust, etc.
7. Float bowl vent or overflow tube clogged.
8. Fuel flow to carburetor restricted.
9. Intake manifold leak.
10. The gas cap is not venting properly or fuel tank venting system blocked.
11. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
12. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Bike idles perfect but dies when given the slightest amount of throttle 93...
starts idles stalls giving gas Scooter Doc Forum
scooter dies if give it throttle
http://www.scootermasters.com/manuals/kymco%20People%2050-complete.pdf

Aug 27, 2016 | Kymco Motorcycles

1 Answer

My kymco 50cc starts but when you go to throttle it it cuts out can you help


Hi, Christopher and the usual suspects are:
1. Idle circuit and transfer ports clogged.
2. Air fuel mixture adjustment too lean.
3. Pilot jet clogged.
4. Faulty accelerator pump.
5. Float level too low.
6. Float bowl contaminated old fuel, water, dirt, rust, etc.
7. Float bowl vent or overflow tube clogged.
8. Fuel flow to carburetor restricted.
9. Intake manifold leak.
10. The gas cap is not venting properly or fuel tank venting system blocked.
11. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
12. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.scootermasters.com/manuals/kymco%20People%2050-complete.pdf
scooter dies if give it throttle
starts idles stalls giving gas Scooter Doc Forum
Bike idles perfect but dies when given the slightest amount of throttle 93...

Aug 27, 2016 | Kymco Motorcycles

1 Answer

Where is the air intake temperature sensor on my 1998 Vw Jetta GLX


It should be located on the side of your intake manifold. It will be a screw-in fitting with a couple of wires connected to it.

Mar 24, 2014 | Vehicle Parts & Accessories

1 Answer

98 ford explorer running to lean, replaced fuel pump, mass air flow sensor and checked for vaccuum leaks. Any suggestions? we are at a complete loss at this point. Please help


spray carb/choke cleaner under intake on mating surface to lower intake. go around the whole intake, dont be shy but spray it.(motor running) does rpm change? if bad seal Usually rpm raises. if so replace intake gaskets, $22.00 parts. Is check eng light on? if yes code check it.although it will only read lean as it cannot detect air leaks. if no code or light carb cleaner is the way to check for air leaks. NOT STARTING FLUID!! I just finished this repair on my 98 tonight, 1-6-11 it runs great, idles also.

Dec 31, 2010 | 1998 Ford Explorer

1 Answer

Birds in flu


Buy a small piece of chicken wire.
One additional piece of PVC pipe, and a coupling.

Cut the chicken wire the exact size of the outside diamiter of the pipe, place it on the end of the pipe and install the coupling over it.

The chicken wire "screen" will be help in place by the pipe wall, the internal ring on the coupling, and the PVC glue. Cut the pipe to the length you need and install it on the intake pipe outside the wall.

Oct 06, 2009 | Weather King 10AJA4801AH Air Conditioner

1 Answer

Aircon pipes dont fit


the refrig doods use out side diamiter. 1/2" pluming pipe is called 5/8" in refrig. we use a reducer to go 1/2 od to 3/4" od, or we swedge one to get the smaller to fit inside the larger and soder. add flairs to the finished size pipe

Feb 17, 2008 | Heating & Cooling

Not finding what you are looking for?
2001 Kymco Stryker 125 Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...