Question about 2000 Suzuki VL 1500 Intruder LC

Open Question

Loud wining noise on deceleration or when coasting. No noise can be heard when under load or accelerating.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SuperTech-11
  • 1591 Answers

SOURCE: Clunking noise with 2009 Suzuki

Check the drive shaft for wear and proper seating etc.
If the drive shaft checks out OK, then you might want to check the piston bearings.

Posted on Jul 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are some of the signs that transmition cluch plate is going out?


first question =---manual or automatic
next are there any other symptoms ( slipping, shudder on take off, difficult to select 1st gear or reverse )
I would be looking at the drive shaft "U" joints and cv joints first because once a clutch is engaged there will be no noise under acceleration of deceleration
look for failed engine/transmission mounts and suspension rubbers worn out

Oct 25, 2015 | 1993 Dodge Dakota

1 Answer

Loud knocking noice under front end when accelerating while turning hard left.


Broke engine mount if its making the noise on acceleration or on deceleration I have seen this alot on Chrysler and some honda .

Jan 22, 2014 | Transmission & Drivetrain for Lexus LX470

1 Answer

Grinding/whining noise from gearbox/final drive - fiat 500C Lounge - 2010 model


I think removes the tyre both then check its gear box bearing noise or clutch plate bearing noise

Dec 16, 2013 | Cars & Trucks

2 Answers

Loud Vibration / Sound Under Acceleration And Starting Engine.


Get the engine mounts checked. A bad mount may allow part of the engine to lie on a body or frame part, allowing engine vibrations to become very loud. Torquing of the engine (under load) can cause the same type problems.

May 03, 2017 | 2005 Dodge Neon SE

1 Answer

I want to know how to use my cruise control in my 1994 Toyota pickup. It has all the buttons and the capability but the words are scratched off and i don't have a manual.


Generally... There is ON/OFF - SET - ACCELERATE/RESUME, COAST/DECELERATE. Cruise is available at speeds above 35mph or so. Sometimes there is no main on/off. Cruise on a turn signal stem has a button that pushes in on the end, push when at desired speed. resume/accelerate slides to right, is spring loaded and return left when released. the same lever when slid left is coast/decelerate. Momentarily sliding accelerate and releasing increases crusing speed by a couple mph. If brakes are used cruise disengages, sliding resume returns you to cruise speed after braking. Coast/decelerate disengages cruise, when at desired lower speed hit set. On some, hitting set not needed, when coast is released speed is maintained. Variations may be up/ down instead or may be steering wheel face mounted. Please rate answer. Duct tape is like the force, it has a dark side.. a light side.. and holds the universe together!

Jun 12, 2010 | Cars & Trucks

1 Answer

ABS Light Came on and Loud Whining in Rear End?


Well you can remove the sensor in the diff and make sure that looks ok they g obad quiet often also woulnd not hurt too remove the rear diff cover and inspect the rear end if it is whining and you dont see anything wrong i would refill it with lucas oil/grease and start praying check the pinion too and see if it has any play in it

Jan 17, 2009 | 2004 Ford Ranger

1 Answer

Loud Intermittent Droaning Noise


rear axle to ring gear side bearing is loose due to weak preload. might be able to locktight is its not to late. was in bmwmoa memeber mag this month december08

Nov 30, 2008 | 2004 BMW R 1150 RT (ABS)

Not finding what you are looking for?
2000 Suzuki VL 1500 Intruder LC Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...