Question about 2005 Yamaha V Star Classic
Hi, Try1st and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Fuel line to carburetor or throttle body pinched or kinked.
8. Carburetor float stuck.
9. Fuel injectors clogged.
10. Severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
11. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
12. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
13. Ignition timing incorrect due to a faulty ignition coil, ignition module or sensors (MAP, CMP, CKP, O2, TPS, ETP, IAC,or BAS).
14. Faulty neutral, clutch lever, or kickstand safety switch.
15. Faulty fuel pump or fuse or relay.
16. Faulty CDI box if applicable.
17. Tilt sensor needs a reset.
18. Security system not disarming alarm needs a reset.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
V650 won start in 650 Star Tech Forum
VStar 650 won start
OEM parts for Yamaha
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Jun 13, 2016
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
i use a jump box on mine most weekends when i wanna take it out, i hook the red to battery and black onto my exhaust and it fires right up no problem. is the clicking noise coming from the fuel pump behind the ignition? it should click for a few seconds then stop. if it stays on then you are not getting enough fuel outta the tank, change the fuel filter and if bike had been stored for winter get a good fuel system cleaner, additive type. if in USA get Berrymans B12, double dose get bike to run hopefully let it stand overnight and all should be fine. fingers crossed. if is is clicking from somewhere else like starter or a relay by the battery, check all the ground terminals you can find
thats a link for a free pdf service manual
my 99 v star
Posted on Apr 04, 2009
I had the same problem 2001 XVS1100 Custom
this is a starter issue Over time the starter on this bike twists when its under a load.
Look at the two bolts holding the starter on if they are not straight across then its twisted. turn starter back in line with a pair of big channel locks and try to start this should do the trick if this works i would recommend taking the two bolts out and bend them back straight or replace and reinstall starter this should fixya problem
Hope this helps ...............Jimmyfixya
Posted on Jul 08, 2009
Sounds like it may be drawing air around the intake somewhere. Let it idle and spray around carefully with wd-40 until it speeds up. This will reveal the leak.
Posted on Oct 11, 2009
Tips for a great answer:
Jul 06, 2014 | 2009 Yamaha V Star 950 Base
Feb 07, 2014 | 2006 Yamaha V Star Classic
May 31, 2013 | 2011 Yamaha V Star 950
Oct 07, 2012 | 2009 Yamaha V Star 1300
Aug 01, 2012 | 2001 Yamaha XVS 125 Dragster
Oct 17, 2011 | 1991 Yamaha Xv 250 Virago S
Feb 04, 2011 | 2005 Yamaha V Star 1100 Classic
Oct 07, 2010 | 2000 Yamaha V Star Classic
Jun 06, 2010 | 2007 Yamaha V Star Classic
May 07, 2010 | 2004 Yamaha V Star Classic
Jul 09, 2018 | Motorcycles
124 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: