Question about 2003 Honda VT 1100 C2 Shadow Sabre

1 Answer

What is the proper configuration for the retainer clip in the headlamp for a 2003 Honda VT1100?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

Copy and paste the link below in your browser,and it will show you how it sets
http://partsfinder.onlinemicrofiche.com/wps_dealer_orders/Honda_OEM/HondaMC.asp?Type=13&A=369&B=30

Posted on May 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda Shadow VT1100 Ace shuts off when shifted into gear


Hi, Wayne and the usual suspects are:
1. Faulty wiring to any safety switch.
2. Safety switches loose at the mounting point.
3. Faulty kickstand safety switch.
4. Failed kickstand safety switch circuit diode.
5. Stretched side stand spring.
6. Side stand not coming up far enough to disengage switch.
7. Faulty clutch lever safety switch.
8. Faulty neutral safety switch.
9. Clutch not properly adjusted.
10. Clutch plates sticking, forward lurch
For more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Dies when put it in gear 2003 Honda Spirit VT 750
Engine dies when put into Gear
Honda SHADOW VT1100 Owners Workshop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda Shadow VT1100 Owner Manual

Jun 18, 2017 | Honda VT 1100 C Shadow Motorcycles

1 Answer

Gear ratio on a 2003 honda shadow sabre 1100


Hi, Toms for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
The Difference between VT1100 Spirit and VT1100 Sabre
2003 Honda VT1100C2 Shadow Sabre
Honda shadow vt1100 Owners Workshop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda VT1100C2 Owner Manual

Jan 18, 2017 | Honda Motorcycles

1 Answer

How to remove headlight housing 2001 FLSTC



To remove the headlamp housing assembly disconnect the wiring harness and then remove the bolt underneath the housing and ligt the housing off the mount.

To change headlamp bulbs:

2001 FXSTD, FXSTS and FLSTS Models

Remove the trim ring screw and then the trim ring, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.
2001 FXST and FXSTB Models
Loosen the trim ring screw and remove the trim ring, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.
FLSTC and FLSTF Models
Except for HDI motorcycles which have a Halogen bulb similar to FXST the FLSTC and FLSTF motorcycles have a sealed beam type headlamp. HDI headlamps also contain a position lamp bulb that is found under the headlamp assembly's rubber boot.
Remove the trim ring screw and then the trim ring, being careful not to bend the two tabs that hold the
top of the trim ring in place, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.

May 17, 2014 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

Loose (noisy) Headlamp when driving


Take it apart & check that all clips are still there & connected properly, this happened on my cafe racer headlamp when one of the W clips came loose causing the reflector & glass to move in the outer heaslight case wich caused squeeks & rattles

Sep 15, 2012 | 2006 Honda ANF125 Innova

2 Answers

How do I replace front headlight bulbs?


To replace a headlamp bulb, do the following:

1. Open the hood.

2. Remove the rubber

cover and socket from
the headlamp.

3. Release the retainer clip holding the bulb by

pressing down and moving the metal retainer away

from you.

4. Pull the bulb out of the fixture.
5. Reverse the steps to install a new bulb.
You can get a free owners manual at this site (where i got your info)
http://www.automanualonline.com/base/chevrolet/tracker/2003/2003-chevrolet-tracker-owners-manual/
It's free just enter the code they give you and Save or Open it. I'd save it. The site is safe.

Mar 10, 2011 | 2003 Chevrolet Tracker

1 Answer

Where is the wiper motor located


Section 17-01: Lighting, Exterior 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Headlamp Assembly Removal and Installation
  1. ssa~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HEADLAMP BULB AND RETAINER (13N021) ARE DROPPED. HANDLE BULB CAREFULLY. GRASP HEADLAMP BULB AND RETAINER ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HEADLAMP BULB AND RETAINER OUT OF REACH OF CHILDREN.
    NOTE: The headlamp (13008) on this vehicle does not need replacement when the headlamp bulb and retainer burns out. Refer to Headlamp Bulb for removal and installation of headlamp bulb and retainer .
    Position headlamp in the OFF position.
  1. Remove headlamp dash panel junction wire (14290) from headlamp bulb and retainers by grasping wires firmly and carefully snapping connector downward.
  1. NOTE: Use snap-ring pliers to spread headlamp mounting clips (13N129) , then pull straight upward to disengage.
    Remove three headlamp mounting clips attaching headlamp to radiator grille opening panel reinforcement (8A284) .
  1. Remove headlamp from vehicle.
  1. To install, reverse Removal procedure.
  1. Aim headlamp .

Oct 21, 2010 | 1999 Mercury Grand Marquis

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    How to change a headlight bulb on a 2002 Harley Davidson Dyna Wide Glide


    REMOVAL

    Do not ever touch the quartz bulb with your fingers as fingerprints will etch the glass and cause the bulb to fail prematurely.


    FXD, FXDL, FXDX Models

    Loosen the trim ring clamp screw and nut, remove the trim ring, pull the connector block from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to unhook and release them from the from notches in the headlamp assembly, pivot the wire retaining clip away from the bulb aqnd then remove the bulb from the headlamp assembly.


    FXDWG, FXDXT Models

    Loosen the trim ring clamp screw and remove the trim ring, pull the wiring connector from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to unhook and release them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb and remove the bulb from the headlamp assembly.



    INSTALLATION

    Install a new bulb and assemble the headlamp components in the reverse of the removal process. Align the headlight when it is fully installed. When reassembling the headlamp ensure that the slots and tabs in the headlamp, adapter ring, and trim ring are aligned.

    Jul 12, 2010 | 2002 Harley Davidson FXDWG Dyna Wide Glide

    1 Answer

    2003 Mercury Mountaineer


    No you don't have to remove battery.
    Look on the back side of the headlamp assembly and you will see to black retainer clips.Pull up on them and this releases the headlamp assembly,pull it forward then replace bulb reinstall the assembly and then push the retainer clips back down.

    Feb 12, 2009 | 2003 Mercury Mountaineer

    Not finding what you are looking for?
    2003 Honda VT 1100 C2 Shadow Sabre Logo

    Related Topics:

    87 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4533 Answers

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    bazzz7071
    bazzz7071

    Level 2 Expert

    342 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...