Question about Honda VT 500 C Motorcycles

1 Answer

Can you please tell me were you put the coolent in a vt500e

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 952 Answers


Thanks for using FixYa again.

All you need to do is to mix coolant and water in your radiator. A 50/50 mixture would be nice. Make sure that you use distilled water.

I hope this helps. Thanks and good day.

Posted on May 15, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i line up timing marks on a 1984 Honda vt500c

[PDF]1986 Honda 200 Timing Marks
honda 200 timing marks We have made it easy for you to find 1986 honda 200 timing marks without ... 1984 - 1985 CB14L-A2 Honda 700 CB700SC Nighthawk u0027Su00271984 - 1986 .... VT500FT Ascot, VT500C Shadow,VT500E Euro .

Aug 08, 2015 | Honda Motorcycles

1 Answer

Coolent fans wont run

Open the bottom of the fuse / relay box, look for burnt/ damaged wiring under where the fan relays mount.

Jan 08, 2014 | 1999 Chevrolet Venture

1 Answer

Honda vt500e leaking water pump how to fix

replace the water pump or mechanical seal .. or both

Aug 03, 2013 | Honda CR 125 R Motorcycles

1 Answer

Hi my f150 2000 is overheating i just changed the thermastat and drained the coolent but it still over heat's from the tank were i put the coolent in it's like it does not move through the truck it...

I hope you had change the thermostat with the same heat range with old one. If you there is no liquid flow, you need to check the liquid/water pump. In long time use , the water pump can get weared on its impeller / blades. Another thing need to check is your coolant/radiator fan. Why the the terminal in relay box get melted? It can tell us two things. the first is LOOSE connection ( please the power connection - it should secured fitted). Second thing is your FAN. Is it running smooth? If your fan running rough and noisy, the bearing could be a problem. If it running intermittently the carbon brush coukd be a problem.
So please narrow down the problem first before get it fixed

Best Luck

Aug 05, 2011 | 2000 Ford F150 Flareside SuperCab

1 Answer

Coolent tempeture low

engine is telling you that either the temp sensor is dirty or the thermostat is going bad.

Jan 09, 2010 | 2002 Volvo S80

1 Answer

Cannot replce allen bottom of fork

if you have fork disconnected from triple tree this could be have to have it secured in place or connected back on to the forks to keep it it from rotating as you try to tighten it.

Oct 06, 2009 | 1987 Honda VT 500 C

2 Answers

Car still overheating after i put in coolent

First, disconnect your negative battery terminal for 3-5 minutes, this will clear out any old code readings. Re-attach the neg battery cable, start the car and let the car idle until the problem re occurs. If you have a bad thermostat, then lower radiator hose will be significantly cooler then the upper radiator hose. This is because the thermostat has become locked in the closed position and is not allowing coolant to travel through the motor and back to the lower radiator hose. Also, if you do replace your thermostat, make sure to buy a thermostat rated for 1090 or 190, don't use a 180 rating. Using a hemostat with a different rating, can cause other components of the cooling system to work improperly, refer to your owner’s manual or a Haynes/Chilton manual to be absolutely certain.

May 27, 2009 | 1990 Buick Century

2 Answers

I'd like to replace my radiator .What are the basic things to do and what tools are necessary

get ready .. antifrez pan new hoses clamps 10mm.12mm.14.. mm. sockets rachet drain the radiator from lower hose star the car for about 5 seconds . this way the car draints out all the ant.

Feb 25, 2009 | 1995 Toyota Corolla

1 Answer

Heat does not work

you can find the coolent lines into the heater through the fire wall disconect them and put pressure through the core to see if its clogged other than that possably a coolent flush cause stuff builds up in the antifreeze and clogs the lines. your heater uses the heat from the engine coolent to heat the air in the heatercore so naturally if you got bad coolent you got heating problems too

Jan 11, 2009 | 2001 Jeep Cherokee

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

75817 Answers


Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides