Question about Motorcycles

1 Answer

Lurches forward when put in first gear from neutral

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Your clutch is not fully engaging. Tighten your clutch cable if too loose. Bleed the system if it is hydraulic.

Posted on May 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 roadking, not going into gear, starter just spinning while bike is in neutral, in gear bike just free-wheeling push the starter and bike lurches forward but then starter just spins


Hi Rod, sounds like your starter drive is going south. I'm sorry you can't find the first and very best tool your Road King ever needed, but don't despair for a mere $6.50 you can download another one at the website below:
Harley Davidson Manuals Mark Workshop
Good luck and enjoy the video.

Mar 26, 2014 | Harley Davidson FLHR-FLHRI Road king...

1 Answer

Cannot change gear when engine running, when put into gear and then start engine car lurches forward. i figure its the clutch but mech says it may be gearbox


Not the trans, the clutch is not releasing. The clutch may be shot or the release mechanism may not be working. This could be linkage , a cable , or a hydraulic master cylinder & slave cylinder

Jun 08, 2011 | Ford Ranger Cars & Trucks

1 Answer

Engine shuts off when put in gear, could by kickstand switch, but could the clutch need bleeding?


Hi
Unlikely that the clutch needs bleeding unless she lurches forward when she dies
It will be side-stand, clutch or neutral lockout switches or the relay

Ride Safe
Bike-Doc

Dec 04, 2010 | 2001 Honda VT 1100 C2 Shadow Sabre

1 Answer

My troybilt lurches forward and you can't hold onto it. I bought it used and the belt was slipping but no lurching problem- After the shop put on the new belt. It lurches forward when you start to...


This is normal for these. The belt slipping before absorbed this. The only real way to prevent this is to weigh the tiller down with large rocks, concrete blocks, something of that sort. They have been built much lighter since Troy-Bilt was bought by MTD, and don't weigh enough to keep from picking up and taking off when you use it. I have a small one, and I weigh it down with about 150 lbs of concrete and lead, and that does it.

May 28, 2010 | Garden

1 Answer

Lurches forward when put in first gear from neutral


Readjust cluch it's not disengageing.Adjusting cable at clutch lever should do it.

Mar 21, 2010 | Honda CMX 250 Rebel Motorcycles

1 Answer

2004 Camry lurches forward when stopping.


Sounds like the torque converter isn't unlocking quick enough. Drive at 45mph,keep foot on gas and use other foot to touch the brake and watch the tach to see if it speeds up,when converter releases. Check trans fluid level hot.If it is more than a couple years old,change. Use the correct fluid for Toyota and add a bottle of Lubgard. Have the throttle positon senor scanned and check any idle control circuits. Throttle Body may need cleaning.

Mar 11, 2010 | 2004 Toyota Camry

1 Answer

1991 Crown Vic dies in reverse and park


SOUND LIKE THE LOCK UP IN TORQUE CONVERTER IS BAD BUT IT IS IN TRANSMISSION YOUR PROMBLEM

Aug 19, 2009 | 1994 Ford Taurus

1 Answer

My 250 honda rebel runs fine in neutral but shuts off when i put it in gear. When i don't have the cluch engaged it lurches foward slightly then shuts off.


Check the side stand kill switch. Broken, loose or out of adjustment it will kill the bike when put in gear. The idea is to prevent starting out with the side stand down. Check the wires and connections also.

Jul 01, 2009 | 2000 Honda CA 125 Rebel

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...