Question about 2005 Kymco Venox 250

2 Answers

Venox 250 (2007). Whats the knob for on the right side of the cycle, approximately opposite the choke knob on the left side?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

It's the idle speed adjustment. Forward (clockwise) for faster/higher idle, back for slower.

Posted on May 16, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

It is to ajust your idel speed all it does is connects to the carb and it screws in and out to increase or decrease the idel speed

Posted on Jul 01, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Faulty fuel delivery


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a "LOAD" test if necessary, your battery may show 12.5 volts but have little or zero amps and needs to be replaced.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, points/condenser ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Accelerator pump damaged or not working.
11. Water or dirt in the fuel system, carburetor or filter.
12. Restricted, blocked or kinked fuel line.
13. Fuel tank empty.
14. Fuel tank contaminated with ethanol sludge.
15. The gas cap is not venting properly or fuel tank venting system blocked.
16. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
17. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the blue links below. Good luck and have a wonderful day.
Why is my 2005 Venox running horrible
bike shuts off while riding please help Suzuki GSX Motorcycle Forums...
KYMCO VENOX 250 Service Manual
Quality Replacement Parts For Kymco
http://www.kymcousa.com/owners/onroad/Venox250.pdf

Apr 23, 2017 | 2005 Kymco Venox 250

1 Answer

WFW9200SQ Cycle Control knob


Fixya cannot recommend part numbers.

Jul 27, 2017 | Washing Machines

1 Answer

I started my bike today with choke out when i thought it was all set to go, i put it on first gear and it turns off. first time having issues with bike.


Hi, You probably did not need the choke because it was warm out side. Also do the maintenance change the oil , filter and sparkplugs. Good luck.

Jun 28, 2011 | 2005 Kymco 250 Venox

1 Answer

Choke knob is very hard to pull? What could be wrong and whats needed to fix?


There is a tension adjusting bezel at the base of the choke knob. Loosen it to free up the choke action. It is a black plastic ring around the choke shaft. If the choke cable itself is not seized up, this should do the trick.

May 30, 2011 | 2002 Suzuki VL 800 Volusia

1 Answer

Bike will not idle without the choke ingaged?


The idle adjustment is on a small knob under the left side of the fuel tank. Start the bike as you would normally, then turn the knob until the idle speed picks up and slowly work the choke in. Continue making these small adjustments until the choke is all the way in and the bike is idling at a speed that is to your satisfaction. Barring any mechanical problem, this should do the trick.

God bless and good luck.

May 02, 2011 | 2001 Suzuki VL 800 Volusia

1 Answer

How Do I Set My Clock on My Kenwood KDC-MP208?


1:- Select Clock Adjustment mode Press the top or bottom side of the Control knob. Select the "ClK ADJ"/ "ClCK" display. 2:- Enter Clock Adjust mode. Press the centre of the Control knob for at least 1 second. The clock display blinks. 3:- Adjust the hours. Press the top or bottom side of the Control knob. Adjust the minutes Press the right or left side of the Control knob. 4:- Exit Clock adjustment mode, Press the [B.BOOST] button.
Now whats the time, Gotta get my tea.
Regards, Dave

Mar 20, 2011 | Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

How do i remove the seat to get to the battery


There are three screws holding the seat down. One at the back which is easy to see the other two you need to remove each top side cover (left & right) to access the other two. More info here

Apr 10, 2010 | 2003 Kymco Venox 250

1 Answer

How do you change the dryer door from a left to right opening to a right to left opening. Thid is a series 90 kenmore


Open the dryer door. There should be approximately three screws that hold the hinges on there on the right side (as you said yours currently is a left to right opening). Remove the screws that hold the door on. As you hold the dryer door removed from the dryer, turn it counter clockwise so that the handle is now on the opposite side. Lay it on the floor. Now, remove the screw hole covers from the opposite side of the dryer opening ( the left side) (these can be removed with a fingernail or a thin flat tipped screw driver to pry them out). This will expose the screw holes on the opposite (left)side of the dryer. Take the removed covers and place them in the original screw holes on the right side. Now simply reinstall the door hinges in the newly exposed screw holes on the left side. This will only work if your dryer is designed to have both types of openings. Good Luck!

Feb 27, 2010 | Kenmore 659 Electric Dryer

1 Answer

Right side stove top igniters dont fire off of right side knobs+


clean the pilot jets out sonds as if they are clogged. if the right side is only being lit once the left side is on then you better not run the right until you do get it fixed as more than likely whats happening is the enough gas is traveling through the chamber to be ignited by the left sides flame and that can be dangerous, however your stove uses an electronic lighter all you need to do is clean the contact points so that they will spark cleanly if it still won't light you need a repairman.

Dec 07, 2009 | Ovens

Not finding what you are looking for?
2005 Kymco Venox 250 Logo

Related Topics:

383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...