Question about 1999 Suzuki GSX-R 600

1 Answer

I need to get to the spark plugs and change them but i am not sure how and what they look like or whats is a good replacement

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 338 Answers

Remove the seat then the fuel tank and air box you will noticed the 4 wires going to the top center of the head spark plug caps pull the caps straight up and out the spark plugs are in the hole when replacing be careful to thread them in carefully don't force them when turning so you do not cross the spark plug hole.

Posted on May 15, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Huskee LT4200. Turns over. Why won't it start?

Any combustion engine needs 3 things to run...Spark, Fuel, and compression. You need to figure out what you are missing. Easiest thing to check is spark. Pull the spark plug and hold the metal base against metal engine casing, and making sure you are holding onto the insulating rubber of the boot, have someone help crank the engine over while you hold the plug there. Look for a good strong blue to white spark at the plug gap. If you have no spark or weak yellow to orange spark you will need to look into the ignition system. New plug is the cheapest and easiest thing to change and test again. If it is still a weak spark then you will need to look to the coil/ ht lead, igniter box, or pick-up. While the plug is out, you can check for compression in the cylinder. If you end up having good spark and good compression then you look to the fuel system. If you can't find a problem with your fuel system, your fuel, spark, and compression also have to happen at the correct you check your timing marks. Simple steps of engine trouble shooting.

Jun 30, 2015 | Cars & Trucks

1 Answer

What cause my 2000 dodge neon to stop on me and now it wont even turn over. and all of the spark plugs is cover in oil?

it is possible that your neg battery terminal could be losing contact or coil could have stopped working and im sure the oil on the spark plugs has a bit to do with the running issue . You need to change the valve cover gasket make sure nothing is cracked clean up the valve cover and engine side surface install valve cover gaskets and bolts torque em down and see what happens youll probably have to replace the spark plugs or clean them up real good

Jan 26, 2015 | 2000 Dodge Neon

2 Answers

Mitsubishi galant V6 replace spark plugs

Are you asking how to replace them?

Jul 04, 2014 | Cars & Trucks

1 Answer

I want to change my spark plugs

First get the spark plugs, then get the right swivel socket for the spark plugs and a gapper for the gap of the spark plugs.

Remove the boot, from the first spark plug, and..

Unscrew each spark plug one at a time (making sure not to mix up the spark plug wires) using a ratchet and extension, and the swivel spark plug socket by turning counter clockwise.

Carefully gap each spark plug, if needed, and insert by hand and slowly screw in each spark plug, making sure not to cross thread.

Put the boot back on to each spark plug, making sure that you squeeze down the connector a little bit to ensure a good tight connection.

Remember, replace one spark plug at a time and replace the boot in order to not get the firing order mixed up.

Aug 27, 2010 | 2000 Renault Sportwagon

2 Answers

4.3 v-6. need to change spark plugs. can hardly see them to change them. what is the best way to change them?

Change all of then through the wheel well, there is a rubber cover that can be flipped up to access all the spark plugs with the spark plug socket and extension.
Note the #3 spark plug on the drivers side, your going to need a spark plug socket with a swivel built in with it to take the spark plug out. The shock tower mount get's in the way and you can only loosen the plug and then your going to have to use your fingers to remove an replace it, then use the socket and extension to tighten it again.
Don't forget to use anti-seize on the new spark plugs for an easier service the next time you replace the plugs.
Good luck and you should not have to raise the s10 up. Thanks for using Fixya

Mar 16, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

What tools will you need to change spark plugs and which spark plugs do you recommend

You will need a socket wrench with a 16mm or 5/8in. socket. You will need a T30 (torx) to remove the plastic cover on the camshft cover to access the plugs. To install:
5- & 6-Cylinder Engines
  1. Be sure the spark plug gap is set to 0.030 inch (0.763mm).
  2. Carefully install the spark plug and tighten to 20-22 ft. lbs. (27-29 Nm).

8-Cylinder Engine
  1. Be sure the spark plug gap is set to 0.028 in. (0.712mm).
  2. Carefully install the spark plug and tighten 18 ft. lbs. (24 Nm).

Make sure to use some plug grease on the threads to keep them from locking up. You will probably need an extention if they are deep. You may need a magnet pen to get the plugs out of the deep hole. Good Luck!

Feb 24, 2010 | 2004 Volvo XC90

1 Answer

It will not start and has no spark. I pulled the plug and let it hang and had no spark. I did the same thing with a spark plug and still no change. Can anyone help me

First of all- your methods of testing spark are ... unsatisfactory.
You need a spark tester and a good unit ground to determine the condition of the module.
For preliminary tests the spark plug needs to be grounded. Insert the plug into the spark plug boot and make sure there is a good connection and make sure the plug is grounded by touching the threaded part of the spark plug to a solid engine component. Usually the cooling fins of the cylinder or head. Once the plug is grounded proplerly then pull the rope and check for fire.
Once you are satisfied that there is no spark then unplug the ground wire from the module and check for spark again. If you have spark then its a switch or bad wire problem. If still no spark then replace the module.

Dec 08, 2009 | Echo Inc. 44 CC, Carb Certified Backpack...

5 Answers

How often do i need to get a tune up and what parts do i need to buy for the tune up?

once or twice a year is good for an actual tune up which is new fuel filter, plugs, plug wires, & antifreeze.
About every other year, you should replace tranny fluid and filter. Not bad idea to have coolant and tranny flushed every 2-3 years too.

Sep 30, 2009 | 1999 GMC Sonoma

2 Answers

I'm changing the spark plugs on my 2004 Toyota Sequoia 4.7 V8 this weekend. I've never changed spark plugs on an import. Is there anything special I need to know? What is the procedure?

First get a Autorepair manual from either Chiltons or Haynes for your toyota and look up tuneups -replacing spark plugs, this should detail everything required ,even to the firing order for the spark plugs. make sure you follow the book to the letter Or you'll be sorry.

Good luck

Jul 11, 2009 | 2004 Toyota Sequoia

Not finding what you are looking for?
1999 Suzuki GSX-R 600 Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

75005 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides