Question about 2003 Suzuki RM 125

1 Answer

Clutch cable how do u fix a new clutch cable on to a rm 125 i have put one on and the clutch is dragging

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 338 Answers

Clutch dragging / slipping? you need to have free play in the cable the lever should not be tight up against lever holder there should be a loose gap.

Posted on May 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Suzuki rm 125, when in gear with the clutch pulled in the bike is always in gear and I can't stop with out stalling i have tried all adjustments on the cable. Any advice


Are you using the correct 10W40W wet clutch motorcycle oil? It has special friction modifiers in it for this clutch drag issue.

Nov 19, 2012 | 2003 Suzuki RM 125

1 Answer

I have an 83 rm 125 and know nothing about bikes!! I went to fire it up after it sitting for about 8 months and it started right up. Problem is when I went to put it in first gear it cuts out...like the...


yes sir that would be the reason i my self have a 2 stroke ts 250 i use automatic transmission fluid for cars in my i have never had a problem all the years i have had mine

Mar 25, 2011 | 2003 Suzuki RM 125

1 Answer

Rm 125 Clutch Problem


84 rm suzuki 125. when i push the clutch in it stays in and dont engage

Jun 06, 2010 | 2003 Suzuki RM 125

1 Answer

2000 suzuki rm 125 have done a complete rebuild on bike new cables new clutch new top end every thing new even down to a complete new bolt kit i used to race and know these bikes in and out but i am...


look for grooves or dents in the clutch basket, that would be holding the disks apart, also make sure the disks all face the same way out.

Mar 16, 2010 | 2003 Suzuki RM 125

1 Answer

91 SUZUKI RM 125 CLUTCH PROBLEM


First, try the cable adjustment at the lever end, if no more movement re-adjust inwards, then adjust at the clutch end.
If no joy, then it is either the lifter mechanism or the clutch its self.
Ride Safe
Bike-Doc

Please mark this as useful (if it has been!!)

Aug 03, 2009 | 2003 Suzuki RM 125

1 Answer

1991 rm 125 clutch springs torque


The clutch springs are not the problem. Check to see if all parts were installed as shown below. The clutch plates alternate Fiber/steel/fiber/steel, starting and ending with a fiber. Be sure the teeth on the clutch rack are pointing to the rear.

A “very helpful” rating for this answer? Thanks!

2043956.gif

Jun 27, 2009 | 2003 Suzuki RM 125

1 Answer

I have a suzuki rm 125 1994 model when i pull the clutch lever in to put it in gear the clutch doesnt work t jst crunches into gear


Adjust the clutch cable to allow about 1/4" free play at the end of the clutch handle. Don't put the bike in gear until the rpms are near idle speed. The clutch is working fine if the bike does not lurch forward when going into gear at idle speed. Dirty, gritty oil in the gearbox can make the clutch grab. Consider changing oil if grabbing is the problem. The "crunch" you hear is the slider gear engaging into the driven gear. The higher the engine speed when being put into gear the louder the crunch. The slider gear engaging "dogs" can break. Crunching into gear is hard on the gears.

Post a comment to let me know how you come out on this.

Jun 04, 2009 | 2003 Suzuki RM 125

2 Answers

Clutch wont dissengage


1) Can you push the bike while it's in gear with the clutch pulled in? [If so, clutch is disengaging OK]

2) If not, check when you pull in the clutch lever that it pulls all the way through to the actual clutch [If not, replace broken clutch cable]

3) If so, clutch is binding. Either fix it properly by stripping the clutch.. or just brute-force the plates apart. :-)

Brute-force clutch plate separation: First make sure you have enough oil in the engine (wet clutch), then basically you're looking at either riding it with the clutch lever pulled in until the plates come apart or with the rear wheel in the air CAREFULLY running it in first gear against the rear brake while the clutch is pulled in.

Mar 20, 2009 | 2003 Suzuki RM 125

2 Answers

1996 rm 125 has clutch problems. The quater inch play does not work, new cable, aftermarket clutch with springs,fibers,steele.


Did you check the main crank drive gear i had a 96 rm 125 with that problem. Its a cheap fix if thats the case but the only problem is that the engine needs to removed and the case needs to be be split. If thats not the problem with the case split it should be ovious.

Mar 18, 2009 | 2003 Suzuki RM 125

Not finding what you are looking for?
2003 Suzuki RM 125 Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...