Question about Honda XR 125 L Motorcycles

1 Answer

To fit front wheel bearings honda xr 125 - XR 125 L Honda Motorcycles

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 85 Answers

Support the bike. Remove front axle nut and remove the axle, releasing the front wheel. Using a flat screwdriver, remove the rubber seals. Use a blunt object that will fit through the axle hole along with a hammer to drive each of the 2 bearings out from the back side. Work by tapping lightly and working around the bearing a little at a time until it pops out. Replace each of the bearings in a similar fashion, working slowly and carefully until the first bearing is in. Install the center bearing spacer tube and install the other bearing. Next replace the dust seals and reinstall the wheel.

Posted on Jun 12, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
bazzz7071
  • 342 Answers

SOURCE: to fit front wheel bearings honda xr 125

Hello unless there something unusual about the front wheel.
bearing removal is not difficult
once you have the wheel off remove the seals on both sides.
remove any internal snap rings or retaining rings.
now the correct way to remove the bearings is with a bearing remover its a shaft with an expandable tip and a weighted slide. when the end is inserted into the center race of the wheel bearing then the shaft is turned to expand the expandable end locking it in place then you use the weighted slide on the shaft to drive it out.
replacing the bearings easiest way is ti use a press not everyone has one of those a bearing driver or and old socket can be used to drive in the new bearings just make sure it is smaller than the inside diameter of the bearing hole and just enough to make contact with the outer bearing race do not force or make contact with the center race.
Hope this helps you out

Posted on May 11, 2010

Testimonial: "many thanks steve!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Honda XR 125 L speedometer cable spins backward


Hi, Chris you have the speedometer drive unit on the wrong side of the front wheel for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
NEW HONDA XR125 XR 125 SPEEDO CABLE ALL YEARS eBay
Honda XR 125 Broken Speedometer Fix
Xr125l Bike 2003 2011 Workshop Service Repair Manual Download Manuals... $15
https://www.partsfish.com/page/oem-parts-for-honda
Honda XR125LK Owner Manual

Feb 21, 2018 | 2005 Honda XR 125 L

1 Answer

2003 Honda XR 125 L overhaul front forks


Hi, Jessica for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
How to Fix Replace Leaking Front Fork Seals on Motorcycle 5QJ8H
HONDA Motorcycle Fork seal replacement
Xr125l Bike 2003 2011 Workshop Service Repair Manual Download Manuals... $15
https://www.partsfish.com/page/oem-parts-for-honda
http://mybikemanuals.com/honda/honda-xr-owners-manuals

Aug 06, 2012 | 2003 Honda XR 125 L

1 Answer

2003 Honda XR 125 L oil change


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Honda XR 125 Oil type change questions
oil change and filter cleaning honda xr 125
Xr125l Bike 2003 2011 Workshop Service Repair Manual Download Manuals... $15
https://www.partsfish.com/page/oem-parts-for-honda
Honda XR125LK Owner Manual

May 27, 2012 | 2003 Honda XR 125 L

1 Answer

HOW MANY WHEEL BEARINGS ON BACK WHEEL HONDA NSR 125


Should be one bearing on back and one on front

Jul 27, 2010 | 2000 Honda NSR 125

1 Answer

To fit front wheel bearings honda xr 125


Hello unless there something unusual about the front wheel.
bearing removal is not difficult
once you have the wheel off remove the seals on both sides.
remove any internal snap rings or retaining rings.
now the correct way to remove the bearings is with a bearing remover its a shaft with an expandable tip and a weighted slide. when the end is inserted into the center race of the wheel bearing then the shaft is turned to expand the expandable end locking it in place then you use the weighted slide on the shaft to drive it out.
replacing the bearings easiest way is ti use a press not everyone has one of those a bearing driver or and old socket can be used to drive in the new bearings just make sure it is smaller than the inside diameter of the bearing hole and just enough to make contact with the outer bearing race do not force or make contact with the center race.
Hope this helps you out

May 10, 2010 | 2003 Honda XR 125 L

1 Answer

Axel equivalent to 97 xr 250


My bad. Sorry about that. I posted my answer as a clarification request instead of as a solution.
As mentioned previously, Google for a salvage wheel.

Now the ratings page will come up. Drive safe. Tombones49

Jun 16, 2009 | 1997 Honda XR 250 R

1 Answer

Steering dodgy on my honda xr 125


two reasons are that you have either slightly bent your front wheel /or front forks or both even the slightest damage to either of these can throw the handling and steering the best thing to do is visit your local bike dealer and have the aliignment checked /before you do that though raise the front wheel off the ground and check for play in wheel bearings hold the suspension with one hand so the steering doesnt turn then with other hand pull and push wheel from side to side if it rocks it will be the bearings

Jan 22, 2009 | 2006 Honda XR 125 L

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4888 Answers

yadayada
yadayada

Level 3 Expert

79847 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...