Question about 2003 Honda XR 125 L

1 Answer

To fit front wheel bearings honda xr 125 - 2003 Honda XR 125 L

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 338 Answers

Hello unless there something unusual about the front wheel.
bearing removal is not difficult
once you have the wheel off remove the seals on both sides.
remove any internal snap rings or retaining rings.
now the correct way to remove the bearings is with a bearing remover its a shaft with an expandable tip and a weighted slide. when the end is inserted into the center race of the wheel bearing then the shaft is turned to expand the expandable end locking it in place then you use the weighted slide on the shaft to drive it out.
replacing the bearings easiest way is ti use a press not everyone has one of those a bearing driver or and old socket can be used to drive in the new bearings just make sure it is smaller than the inside diameter of the bearing hole and just enough to make contact with the outer bearing race do not force or make contact with the center race.
Hope this helps you out

Posted on May 11, 2010

Testimonial: "many thanks steve!"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Honda XR 125 L wiring diagram


Hi, Anonymous for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the blue links below. Good luck and have a wonderful day.
2004 Honda XR 125 wiring diagram Google Search
Honda Motorcycle Wiring Diagrams
HONDA XR125L BIKE 2003 2011 WORKSHOP SERVICE REPAIR MANUAL Download... $10
http://www.partsfish.com/page/oem-parts-for-honda
Honda XR125LK Owner Manual

Aug 22, 2013 | 2004 Honda XR 125 L

1 Answer

Where is the battery on honda xr 125?


it should be located under the seat towards the front!

good luck!

Mar 24, 2011 | 2004 Honda XR 125 L

1 Answer

HOW MANY WHEEL BEARINGS ON BACK WHEEL HONDA NSR 125


Should be one bearing on back and one on front

Jul 27, 2010 | 2000 Honda NSR 125

1 Answer

1993 honda xr 125 runs strong but noticed metal shavings in oil whats the problem


Metal shavings in the oil indicate a pretty serious problem. Where the metal is coming from is the question. Unfourtunately, if the problem is not located inside the right side engine cover where the clutch is, the motor must be torn completely down in order to find it. The more you ride the bike, the bigger the problem is going to get. The bigger the problem, the more it will cost to fix it. I would not hesitate to tear down the engine. The shavings are now in the crank bearings, clutch plates, top end and everywhere else. The inside of the engine will need to be cleaned out. The only way to do it is a complete teardown. The good thing is that while torn down you can install new crank bearings, output shaft bearings, OHC chain and tensioner, and all new seals. You will end up with a nearly new engine.

Jul 22, 2010 | 2003 Honda XR 125 L

1 Answer

To fit front wheel bearings honda xr 125


Support the bike. Remove front axle nut and remove the axle, releasing the front wheel. Using a flat screwdriver, remove the rubber seals. Use a blunt object that will fit through the axle hole along with a hammer to drive each of the 2 bearings out from the back side. Work by tapping lightly and working around the bearing a little at a time until it pops out. Replace each of the bearings in a similar fashion, working slowly and carefully until the first bearing is in. Install the center bearing spacer tube and install the other bearing. Next replace the dust seals and reinstall the wheel.

May 10, 2010 | Honda XR 125 L Motorcycles

1 Answer

Axel equivalent to 97 xr 250


My bad. Sorry about that. I posted my answer as a clarification request instead of as a solution.
As mentioned previously, Google for a salvage wheel.

Now the ratings page will come up. Drive safe. Tombones49

Jun 16, 2009 | 1997 Honda XR 250 R

1 Answer

Steering dodgy on my honda xr 125


two reasons are that you have either slightly bent your front wheel /or front forks or both even the slightest damage to either of these can throw the handling and steering the best thing to do is visit your local bike dealer and have the aliignment checked /before you do that though raise the front wheel off the ground and check for play in wheel bearings hold the suspension with one hand so the steering doesnt turn then with other hand pull and push wheel from side to side if it rocks it will be the bearings

Jan 22, 2009 | 2006 Honda XR 125 L

Not finding what you are looking for?
2003 Honda XR 125 L Logo

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...