Question about 1996 kawasaki ZX-7RR

1 Answer

What bolts hold the ignition,tryn to change out.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 440 Answers

Hi they are special security 'shear-off' bolts that have to be drilled out I'm afraid

Ride safe
Bike-Doc
Please mark this as very helpful (if it has been!!) - it helps my ratings

Posted on May 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i turn of the red imobaliser light. It is not on when key in the ignition only when removed


is lamp in the CLUSTER? (not on ours)
no other lights stuck on (warning?)
are you saying the IMMO lamp glows, key out of car>?
that is a relay stuck. (or bad ignition switch or short there)
what country, this is USA site, so no country and no engine stated.
means all answer are wrong. (guessing)

it has its own theft deterrent ECU. (has power all the time,)
and the Immobilizer to main PCM.
my guess is one of 2 relays bad. (or input key switch bad to relay)
IG1 relay
and ( EFI-EOD) relay. can fail if above is stuck.


25397164-unf1iprsnlx2ajznacse1210-3-0.jpg

Feb 02, 2015 | 2001 Toyota Land Cruiser

1 Answer

Tryn to recover my new pass n email


Microsoft will help ypu with this if you know the answers to the security questions

Jul 16, 2013 | Microsoft Xbox 360 Super Elite (250 GB)...

1 Answer

How to change ignition control module


There should be 6 bolts that hold the ignition coils in place. If you remove those bolts, the coils and the module will come out. However, if stalling is your problem, I have seen far more failed crankshaft position sensors than ignition modules (although they are quite common as well)

Feb 02, 2013 | 1991 Buick LeSabre

1 Answer

Streeling wheel is locked cant turn ignition key


Put pressure on steering(tryn to turn it) wheel all the way to one side doesnt matter which way and at the same time try to turn the key.

Nov 12, 2012 | 1996 Honda Accord

1 Answer

I got 01 yzf r6 I'm tryn to change the dog bone


Hi, Kellywalk310 for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.r6-forum.com/forums/56-suspension-settings/146705-help-changing-back-stock-dogbone.html
R6 lowering links
1999 2002 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Feb 07, 2012 | 2001 Yamaha YZF-R6

1 Answer

Tryn to take tv off wall mount


Doesn't matter what brand TV, rather what brand mount what used. There are ussually retaining bolts or a release of some kind on the bottom of the bracket.

Sep 02, 2011 | Dynex Televison & Video

1 Answer

How to remove two pins holding ignition clyinder lock tumbler from 1994 mercury tracer


Removal & Installation


Before continuing with this procedure, make sure to have available a new steering wheel retaining bolt and two lock cylinder retaining bolts. Once removed, these parts lose their torque holding ability (or retention capability) and must not be reused.

  1. If equipped, disarm the air bag system and disconnect the negative battery cable.
  2. Remove the steering wheel.
  3. Remove the combination switch.
  4. Unplug the wiring connector to the ignition switch.
  5. Remove the ignition and shifter interlock cable mounting bracket bolt and position the assembly to one side.
  6. Remove the four steering column bracket bolts and lower the steering column.
  7. Cut a groove in the ignition cylinder bracket bolts with a chisel and hammer or use a similar method.
  8. Using a screwdriver, remove and discard the bracket bolts.
  9. Remove the ignition switch lock cylinder and bracket.

c17hydro_34.gif

Unfasten the ignition and shifter interlock cable mounting bracket bolt, and position the assembly to one side



c17hydro_35.gif

Use a chisel and hammer to cut a groove in the ignition cylinder bracket bolts-1991-96 models shown; 1997-99 models similar


To install:

  1. Install the new ignition switch and the bracket into position on the steering column tube.
  2. Install the new lock cylinder bolts and tighten the bolts enough to hold the switch in position.
  3. Check for proper switch operation by rotating the key to each position. If necessary, reposition the lock cylinder until it operates properly.
  4. If positioned properly, tighten the retaining bolts until the bolt head shears off.
  5. Raise and position the steering column. Tighten the bracket bolts to 80-124 inch lbs. (9-14 Nm).
  6. If equipped with tilt column, remove the upper mounting bracket retaining pin.
  7. Position the interlock cable bracket. Install and tighten the retaining bolt to 35-53 inch lbs. (4-6 Nm).
  8. Attach the wiring connector to the ignition switch.
  9. Install the combination switch.
  10. Connect the negative battery cable.
  11. Confirm operational status of the air bag system by turning the ignition key to the RUN position and visually monitoring the air bag indicator lamp in the instrument cluster. The indicator lamp should illuminate for approximately 6 seconds and then turn OFF. If the indicator lamp does not illuminate, stays ON, or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
  12. Check the steering wheel, horn and combination switch functions for proper operation.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Nov 20, 2010 | Mercury Tracer Cars & Trucks

1 Answer

Lower dash removal of 93 vw cabriolet to change ignition switch


You'll need to remove the steering wheel, 15/16th inch socket, the column top and bottom cover, remove the 3 screws holding on the turn signal and wiper stocks. Unplug and remove the stocks. Remove the black plastic sleeve on the hub. Remove the 1 allen bolt holding the lock cylinder/switch assembly. Remove assembly, there is a phillips screw holding the ignition switch in the assembly, remove that screw and pull out the ignition switch.

Nov 27, 2009 | 1993 Volkswagen Cabriolet

1 Answer

I need to change my ignition cylendar.


Ignition Lock Cylinder REMOVAL & INSTALLATION 1997–99 Models CAUTION
Some models covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6. NOTE: Before continuing with this procedure, make sure to have available a new steering wheel retaining bolt and two lock cylinder retaining bolts. Once removed, these parts lose their torque holding ability (or retention capability) and must not be reused.
  1. If equipped, disarm the air bag system and disconnect the negative battery cable.
  2. If necessary, remove the steering wheel.
  3. Remove the combination switch.
  4. Unplug the ignition switch wiring connectors.
  5. Remove the ignition and shifter interlock cable mounting bracket bolt and position the assembly to one side.
  6. Cut a groove in the ignition cylinder bracket bolts with a chisel and hammer or use a similar method.
  7. Using a screwdriver, remove and discard the bracket bolts.
  8. Remove the ignition switch lock cylinder and bracket. To install:
  9. Install the new ignition switch and the bracket into position on the steering column tube.
  10. Install the new lock cylinder bolts and tighten the bolts enough to hold the switch in position.
  11. Check for proper switch operation by rotating the key to each position. If necessary, reposition the lock cylinder until it operates properly.
  12. If positioned properly, tighten the retaining bolts until the bolt head shears off.
  13. Position the interlock cable bracket. Install and tighten the retaining bolt to 35–53 inch lbs. (4–6 Nm).
  14. Attach the wiring connector to the ignition switch.
  15. Install the combination switch.
  16. If removed, install the steering wheel.
  17. Connect the negative battery cable.
  18. Confirm operational status of the air bag system by turning the ignition key to the RUN position and visually monitoring the air bag indicator lamp in the instrument cluster. The indicator lamp should illuminate for approximately 6 seconds and then turn OFF. If the indicator lamp does not illuminate, stays ON, or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
  19. Check the steering wheel, horn and combination switch functions for proper operation.
Fig. 1: Unfasten the ignition and shifter interlock cable mounting bracket bolt, and position the assembly to one side

72a6db6.gif
Fig. 2: Use a chisel and hammer to cut a groove in the ignition cylinder bracket bolts — 1991–96 models shown; 1997–99 models similar

9849583.gif

Aug 30, 2009 | 1998 Ford Escort

Not finding what you are looking for?
1996 kawasaki ZX-7RR Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...