Question about 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

Grnd wire for the horn is off where does it

Grnd wire for the horn is off where does it connect

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Is it off at the horn? If it is then there should be a terminal on the horn to connect it to. If it is off at the end that goes to ground on the frame it just needs to be hooked to a good ground location, usually on the the other side of the rubber mount to the horn.

Posted on May 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The horn my nissan elgrand has stopped working i have checked the fuses they are ok


A bad switch or wire or connection of the wire to the horn. Try to jump a wire from positive termananl to the horn connection. If it
works the horn is ok. the problem is wire, possibly relay or connections. Back track the wire from horn to the next connection

Mar 15, 2015 | Nissan Cars & Trucks

1 Answer

How to i replace a horn that has three wires to it when the horn I bought only has 2 connectors


I am not an expert on auto horns, but can solve most electrical problems. Do you have a multimeter? Using the ohm-meter, measure the ohm value between the two wires, and from each wire to the horn mounting bracket (you need contact with un-painted metal. The value between the wires should be low (10-100 ohms) but not zero. This represents the horn coil. The value between each wire and the bracket should be very high (10 kilohms or more). This means the horn coil is not grounded to the bracket.

Now, using the voltmeter, measure the voltage between each wire (from one wire to another). The value should be zero before pressing the horn button, and 12 vdc when the horn button is pressed. I would expect one of the wires will also be zero ohms (ohmmeter) when measured to the car frame or body.

Ok, you are ready to hook up the horn. The auto ground wire(s) are connected to a horn wire that is common with the horn bracket. Or, connected to a black horn wire if both horn wires are isolated from the bracket. Connect the auto switch wire (the one that reads 12 vdc when the horn button is pressed) to the remaining horn wire.

Nov 29, 2014 | 1996 Saturn SL

2 Answers

Bf falcon horn


A horn with a single wire connection will be earthed out internally and through the body fixture. Horns that have 2 connections are either internally earthed as explained and the second terminal is to pass the power over to a second horn . . If both terminals are under the one rivet and insulate from the horn body then It is used in parallel with a second horn If the terminals are separated and attached to different areas of the body and are insulated from the body then one will be an earth wire.

Dec 22, 2013 | Mitsubishi Cars & Trucks

2 Answers

The horn not working dt250, have power to wire at horn . Should a horn sound if connected to a 6 volt battery to test horn?


Does the horn have 2 wires or 1? Newer Yamahas have 2 wires....power to the horn, and then a ground wwire that goes through the horn button. If its a 2 wire....jumper the ground wire to a good ground to try the horn...if that works...check the horn button.
If its a single wire horn...ensure the horn is firmly grounded.

Apr 23, 2011 | 1974 Yamaha DT 360

1 Answer

I have a tti cb radio but the wires have come away from the mic but i dont know what colours go to what number can you help


one should be a ground. look at the board were the wire is.. and its obvious that its a ground pin 1. then should have 3 remaining. one will be tx.. touch the others to ground to see which one makes it tx.. theres your pin 3 tx.. on a galaxy pin 4 is not used. thats rx pin4 cobra radios would have a increase in rx audio when this is connected to grnd. the last would be audio. once you find grnd and tx. reconnect mic and put to pin 2 audio. the last 2 wires that gives it audio..

Nov 05, 2010 | Galaxy Radios Microsystems DX98VHP CB...

2 Answers

How to rewire horn connections from two wire, to one


CONNECT ONE WIRE WITH AN EYELET AND CONNECT THE OTHER TO THE HORN THE ONE WITH EYELET NEEDS TO BE FASTENED TO BODY OR GROUND

Mar 17, 2010 | 2000 GMC New Sierra 1500

2 Answers

What is that thick wire thats connected with a


Its a security wire to keep the radio from being easily stolen!!

Sep 19, 2009 | 1991 Plymouth Sundance

1 Answer

Boat horn not working; fuse is good


TOOL NEEDED (1) DC test light or probe. TROUBLESHOOTING (1) generally a horn just has two wires positive and negative. Test negative by connecting dc test light negative to the negative on the back of the horn. use positive side of dc test light and touch a known positive connection. dc test light should light if not. find clean know ground for horn. Test positive by connecting neg side of dc test light to a know negative connection. use positive side of the dc test light and touch positive side of horn. test light should light up when you touch the horn switch. if dc test light does not light take a jumper wire and connect one side of jump wire to a known positive connection. take other side of jumper wire and lightly touch positive side of horn connection. horn should beep. if horn does not beep replace horn. if horn does beep test and or replace horn switch.

Sep 06, 2009 | Boating

1 Answer

Burned out power switch


bk-hot wht-ntrl gr-grnd on fan bare is grnd

Mar 24, 2009 | Dryers

Not finding what you are looking for?
2000 Harley Davidson FLHR-FLHRI Road king Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...