Question about 2001 Honda CBR 929 RR Fireblade

Open Question

Ok on the dash bord of my 929 i have a

Ok on the dash bord of my 929 i have a light that blinks a trouble code how do i reset that or find out what it mean

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I cant get the trouble codes, when I connect the jumper wire under the dash nothing happens. The check light doesn't blink at all. It runs o.k. at first but when it warms up it runs like ssh it. The


you may not have codes some problems dont cause trouble codes --bad catalyic converter --tune up needed--egr valve --fuel filter --fuel pump failure -to name a few

Apr 25, 2017 | Cars & Trucks

Tip

How To Check & Reset Your 2002-2006 Nissan Altima Service Engine Soon (SES)...


The following directions will help you decode your 2002-2006 Nissan Altima's Service Engine Soon (SES) light and reset it.<br /> <br /> <span style="font-weight: bold;">Obtain The Trouble Code</span><br /> <ol> <li>Turn the ignition key to the ON position and wait three seconds.</li> <li>Put the accelerator pedal to the floor and release it five times in less than five seconds.</li> <li>Wait exactly seven seconds. Put the accelerator pedal to the floor for ten seconds until the SES light flashes.</li> <li>Release the accelerator pedal and start counting flashes to obtain the four-digit trouble code.<br /></li></ol> <ul> <li>Long flashes (0.6 seconds) indicate the first digit of the code; count the blinks one through nine and write down the first digit. (Ten blinks indicates a zero.) </li> <li> The next three digits blink faster (0.3 second) and have a 1 second pause between digits.</li> <li>The ECM code repeats until you turn the ignition key to the OFF position.</li> <li>You can look up the trouble codes in the Service Manual.</li> <li>If you get four blinks of ten, or 0000, the ECM indicates no malfunction.<br /></li></ul> <br style="font-weight: bold;" /><span style="font-weight: bold;">Clear The Trouble Code</span><br /> <ol> <li> Clear the code and the SES light by holding the accelerator pedal down to the floor for 10 seconds or more while the SES light is blinking.</li> <li>When the pedal is released, the ECM will erase the trouble code(s).</li></ol>

on Feb 15, 2011 | 2002 Nissan Altima

1 Answer

Trouble shoot


Hi Anonymous, for more information on your question please visit the websites below and good luck:Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Jul 17, 2013 | 2001 Harley Davidson FXDL Dyna Low Rider

1 Answer

How do you reset all the lights on dash battery abs etc on a mazda 1993 929


Hello and welcome to FixYa!


As a first course of action, I strongly suggest that you have the battery charged. It can be an indication of a weak battery or a faulty alternator. If the battery light still on after charging then the problem will surely be on the alternator itself. If that's the case the alternator should be replaced to resolve the problem.


You may try to reset it to by removing the positive battery connector, letting it sit for at least 5mins. then reconnect it again. This will reset the system and can get the battery light off.


Hope this helps and thank you for using FixYa! Have a good one!

May 22, 2011 | 1993 Mazda 929

1 Answer

I have had the timing belt and kit replaced on my car along with a sensor and my check engine light will not go off so that i can pass the required emissions test for my state


you need to access the trouble code to better define the problem. insert key into ignition. you will need to turn the key to the position just before the engine cranks; the dash lights will be on. now turn the key back one click. You need to do this a total of 3 times ending in the on position( dash lights on-not cranking). Your trouble code will either show on the odometer( if it's digital) or will blink on the check engine light. count the number of blinks-pause-blinks etc. jot the numbers down. You can google the numbers to see what system is at fault.

Sep 17, 2010 | 1996 Plymouth Breeze

1 Answer

I have a blinking exclamation mark in the dash


is it your engine service light thats blinking?
if it is you can reset it on some cars by disconnecting your battery and pumping on your brakes about 10 or more times this should clear up some trouble codes the light should go out if not you should have a mechanic check it out.hope that helped

Feb 04, 2010 | 2004 Mercury Montery

2 Answers

Me and my dad change the heater hose and now my engine light is on and my drive 4 light in the dash board is blinking what should i do


You can disconnect your negative battery terminal, wait five minutes or so, then reconnect it. This should clear the malfunction code. If, however, you have an anti-theft radio, make sure that you have the five digit code to reset it after disconnecting the battery. Disconnecting only one terminal might not effect the radio, but I wouldn't count on it.
If the malfunction code comes back after you disconnect the negative terminal, then something has gone wrong with your repairs.
Hope this helps you.

Oct 25, 2009 | 1999 Honda Accord

2 Answers

The dash Bord wont light up


If all else is working ok, it may just be the fuse supplying the lights. If you confirm it is getting power, then it is possible there is a faulty chip within the binnacle (gauge unit) These can be repaired by specialists in this repair fairly cheaply.

Sep 29, 2009 | 1993 Jeep Grand Cherokee

1 Answer

4 wheel drive wont work


it blinks cause u have problem .
and you have to diagnose to get the trouble code

Sep 14, 2009 | 2002 Ford Explorer

Not finding what you are looking for?
2001 Honda CBR 929 RR Fireblade Logo

Related Topics:

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...