Question about 1985 Honda GL 400

1 Answer

Moter oil - 1985 Honda GL 400

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 440 Answers

Use SAE 10w/40 good quality engine oil

Ride safe
Bike-Doc
Please mark this as very helpful (if it has been!!) - it helps my ratings

Posted on May 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil is coming out top of moter where oilsendingunitis


If you are referring to tubes as the tube where the spark plugs are installed then you probably have worn out gaskets at the base of the tubes. If you pull the spark plug wire out and remove a spark plug, you'll probably find the plug is soaked in oil. I suspect you'll have to remove the valve cover to replace these gaskets/seals.

Jul 22, 2012 | 1996 Honda Accord

1 Answer

Hi i have an 86 jimmy 2.8 and the other day i was driving it and i lost power goin up a hill and it started tapping in the moter like a disiel moter it has oil water and not running hot or smoking but the...


It sounds like you have rod knock in your engine. Stop driving your Jimmy and have a mechanic look at the engine immediately. You may have already damaged your block by having a rod poke through it.

I am only guessing at this since you did lose power. The rod closest to your flywheel might have broken or bent, causing a loss of power under load.

Sorry for your conundrum, and I hope this helped.

Jun 17, 2011 | 1986 GMC S-15

1 Answer

Tecumseh 195cc 7hp engine is very hard to turn over, had to use a bar and socket,after removing the pull starter to turn it over, the oil is clean,not burnt,also removed the plug it was good ,squirted...


You are probably correct by saying the engine is half siezed. Rust will get inside the cylinder if it is not used very often. This is a common problem. You are doing the correct thing by turning the engine over with a wrench while putting oil or penetrating oil down the cylinder. The cylinder usually cleans up after a while of turning the engine. But please note that if this is the case then rust has gotten into the cylinder and it may have caused some damage. I have "broke loose" many engines by using the penetrating oil and turning them over by hand with good success. But this may cause it to use some oil, break a ring, or cause more engine damage. Be careful and good luck. Hope this helps.

Dec 31, 2010 | Yard Machines Garden

1 Answer

2005 5.3 vortec top in no oil pres just got truck good moter or bad moter


have to see if the oil pump strainer is clooged...oil ports clogged??? was the motor taken care of...valve covers loaded up with sludge??? pan comes off the rest is to be looked at...if she was run on no oil pressure I sure would be suspect of this motor being in poor condition. Does it run???? Is it knocking?smoking? banging or clunking? if not put a gauge on the oil pressure sending unit hole and see if it really has no oil pressure or perhaps it has a bad sender?

May 06, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

I amtrying to hook up a moter from a 1993 yamaha


ditch the oiler on the sled cause they will fail. premix your fuel at 40:1 and never worry about it

Nov 21, 2009 | 1985 Yamaha XJ 700 X Maxim

1 Answer

I have drained the oil from my lower unit on my 180 bow rider boat. how do i put the oil back in ? all yhe oil hase drained even from the resivor in the moter compartment . it is a 3litter moter.


Not quite a car question but basically you fill it the opposite way that you drained it. You can purchase a pump at you local marine store that attaches to your quart bottle of lower unit lube.

On the end of the pumps' hose there is a threaded fitting which screws in to where the drain plug goes. leave upper vent plug out.

Pump the oil into the lower unit until it comes out of the upper vent hole.Then remove the hose from the lower unit and quickly replace the drain plug.

Wipe the excess oil off of your hands. :)

Oct 25, 2009 | Chevrolet Silverado Cars & Trucks

1 Answer

Stop motion knob has to be turned sometimes to get machine to run. What can I check? I have made sure the machine is oiled.


check the belt it may need to be replaced.

if you unscrew the screw for the moter a little the moter will drop and put enough pressure on the belt, tighen the srew again and try, can keep making adjustment by lifting moter and tightning the screw a little at a time

Aug 26, 2009 | Necchi Sewing Machines

1 Answer

Rear window wont go up


test moter with batt charger &if it works it your switch if not oil the moter and beat it up don't brak it more but don't go easy on it this works

Aug 11, 2009 | 2006 Jeep Liberty

2 Answers

Oil leaking out of front end behind pulley


to replace a main seal you will need to pull the engine and pull the hormonic blancer off to access the seal

Dec 05, 2008 | 1999 Dodge Ram

Not finding what you are looking for?
1985 Honda GL 400 Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77202 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...