Question about 2003 Suzuki AN 400 Burgman

Open Question

I want change oil in transmission on burgman 400 1998 Pease where is the plug for drain and refill

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: how do I change a headlight on a Suzuki Burgman

you reach under the front of the scooter between the headlight and the fender. find the wire that goes to the connector of the headlight. it is directly behind the headlight. unplug the connector, pull the plug off the headlight. remove the rubber cover/boot off the back of the headlight. this is now the tricky part. there is a clip that needs to be unhooked and moved out of the way. remember how you unhook it because you will have to rehook it when you install the new bulb. this hook is a stiff wire with a loop on one end. push on the loop and move it to one side and it will come off the back of the bulb. the clip is attached and will not come off. you should use gloves to remove the bulb. the oils on your hands are not good for the bulb. use glove on removing just in case the bulb is good and you need to use it again. use gloves to install the new bulb. there is only one way to install the new bulb. there are tabs the extend out from the base of the bulb. you can kneel in front and reach your hand under to install the new bulb while you watch the insertion through the glass. rotate the bulb until you feel the detent that allows the bulb to fit into position. both bulbs have the tabs in the same location, ie. the detent tab is about at the 8 oclock position. replace the clip (insure that it clips on to hold the base), the boot and the connector.

Posted on Jun 28, 2009

  • 2 Answers

SOURCE: im changing the transmission oil 10w40. The manuel

The transmission fill hole is a 10 mm bolt that sticks out about 2" the run out of the hole is a 14mm bolt an 1"1/2 below that. it looks like a bolt to hold on the clutch cover.
I had the same problem till I read the service manual.
Ron W.

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Refill twin cam oil


Hi Anonymous, the engine oil tank is underneath the transmission, the engine oil drain plug is in the front left corner of the oil pan, the transmission oil drain plug is located on the bottom right side of the oil pan. The engine oil fill spout is located in the right front corner of transmission. Good luck

Apr 06, 2014 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

Need assistance on changing oil and primary. Warrenty is out and doing it myself.


The oil drain plug is on the bottom of the transmission as the oil tank is located there. Usually the drain plug is the one closest to the left front of the pan. Drain the oil, change the filter, and add fresh oil. To change the primary, locate the small pipe plug on the bottom of the primary directly below the derby cover and remove it. Drain the oil, remove the derby cover, and stand the bike straight up. Fill the primary with oil just until it comes up the bottom of the outer clutch drum. Do not overfill. To change the transmission lubricant, locate the pipe plug on the front of the oil pan on the bottom of the transmission. Drain the oil and refill though the plug and dipstick in the chrome release cover on the right side of the transmission. Add 20-24 ounces of oil.

Good luck
Steve

Jun 05, 2011 | 2004 Harley Davidson FLHRCI Road King...

1 Answer

I need to due an oilm change on a recently perchased '88 sofrtail with 5 speed and belt drive.what do I need to do?


Find the oil drain. It's located below the transmission on the frame behind the exhaust pipes. It may be a hose with a plug in it or the hose my plug onto the crossmember of the frame in that area. If it's in the crossmember, the drain plug is underneath the crossmember. Remove the plug and drain the oil. Replace the oil filter with a new one. Refill the oil tank with three quarts of 20W50 oil. Check the oil after your run the engine long enough to get it to normal operating temp. There are two marks on the dipstick. The top mark is "FULL HOT" the lower mark is "FULL COLD". Do not overfill and check the oil with the bike on the side stand.

To change the oil in your primary, Look below the rear of the outer primary cover way back where the clutch is loctated. Drain the oil and remove the derby cover. Stand the bike straight up and refill the primary with H-D Primary Lube. Fill the primary until the level of oil is just below the lowest portion of the clutch spring in the clutch pack. Do not overfill as the clutch will drag and you will not be able to find neutral position in the transmission with the engine running. About a quart of lube is sufficient.

The transmission drain is a pipe plug on the right side of the transmission. Drain and refill with 20-24 ounces of H-D transmission lube.

Your bike originally came from the factory with H-D Syn3 synthetic 20W50 engine oil in all three areas.

Good Luck
Steve

Feb 05, 2011 | 2003 Harley Davidson FXSTS Springer...

2 Answers

How often should I change the Transmission fluid, normal driving ? Thank you Gary


It's listed in your owner's manual. Schedule A is normal driving conditions.
SCHEDULE "A"
7,500 miles (12 000km) or at 6 months
- Change engine oil.
- Replace engine oil filter.

15,000 miles (24 000km) or at 12 months
- Change engine oil.
- Replace engine oil filter.

22,500 miles (36 000km) or at 18 months
- Change engine oil.
- Replace engine oil filter.
- Inspect front wheel bearings.
- Inspect brake linings.

30,000 miles (48 000km) or at 24 months
- Change engine oil.
- Replace engine oil filter.
- Replace engine air cleaner filter.
- Replace spark plugs.
- Drain and refill automatic transmission fluid and filter (4.7L).

37,500 miles (60 000km) or at 30 months
- Change engine oil.
- Replace engine oil filter.
- Drain and refill automatic transmission fluid and filter (5.2L/5.9L).
- Drain and refill transfer case fluid.

45,000 miles (72 000km) or at 36 months
- Change engine oil.
- Replace engine oil filter.
- Inspect front wheel bearings.
- Inspect brake linings.
- Flush and replace engine coolant at 36 months, regardless of mileage.

52,500 miles (84 000km) or at 42 months
- Change engine oil.
- Replace engine oil filter.
- Flush and replace engine coolant if not done at 46 months.

60,000 miles (96 000km) or at 48 months
- Change engine oil.
- Replace engine oil filter.
- Replace engine air cleaner filter.
- Replace ignition cables (5.2L/5.9L).
- Inspect PCV valve, replace as necessary.
- Replace spark plugs.
- Inspect auto tension drive belt and replace as necessary (5.2L/5.9L).
- Drain and refill automatic transmission fluid (4.7L).

67,500 miles (108 000km) or at 54 months
- Change engine oil.
- Replace engine oil filter.
- Inspect front wheel bearings.
- Inspect brake linings.

75,000 miles (120 000km) or at 60 months
- Change engine oil.
- Replace engine oil filter.
- Drain and refill automatic transmission fluid and filter (5.2L/5.9L).
- Drain and refill transfer case.
- Flush and replace engine coolant if it has been 30,000miles (48 000km) or 24 months since last change.
- Inspect auto tension drive belt and replace if required.

82,500 miles (132 000km) or at 66 months
- Change engine oil.
- Replace engine oil filter.
- Flush and replace engine coolant if it has been 30,000miles (48 000km) or 24 months since last change.

90,000 miles (144 000km) or at 72 months
- Change engine oil.
- Replace engine oil filter.
- Replace engine air cleaner filter.
- Replace spark plugs.
- Inspect front wheel bearings.
- Inspect brake linings.
- Inspect auto tension drive belt and replace as necessary.
- Drain and refill automatic transmission fluid (4.7L).

97,500 miles (156 000km) or at 78 months
- Change engine oil.
- Replace engine oil filter.

105,000 miles (168 000km) or at 84 months
- Change engine oil.
- Replace engine oil filter.
- Flush and replace engine coolant if it has been 30,000 miles (48 000km) or 24 months since last change.
- Inspect auto tension drive belt and replace if required.

112,500 miles (181 000km) or at 90 months
- Change engine oil.
- Replace engine oil filter.
- Drain and refill automatic transmission fluid and filter (5.2L/5.9L).
- Inspect front wheel bearings.
- Inspect brake linings.
- Flush and replace engine coolant if it has been 30,000 miles (48 000km) or 24 months since last change.

120,000 miles (192 000km) or at 96 months
- Change engine oil.
- Replace engine oil filter.
- Replace engine air cleaner filter.
- Replace ignition cables (5.2L/5.9L).
- Inspect PCV valve, replace as necessary.
- Replace spark plugs.
- Inspect auto tension drive belt and replace as necessary.
- Drain and refill automatic transmission fluid (4.7L).

Thanks for using FixYa -a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 05, 2010 | 2001 Dodge Durango

1 Answer

Procedure to change manual transmission fluid, 1995 honda accord.


There are two plugs on trany , one drain , one refiil.
Lift car and level it , open refill plug , set aside.
Open Drain plug and drain the oil.
Reinstall drain plug.
Use sifon pump to pump oil in to refill hole.
Fill it up untill oil start coming out of refill hole.
Reinstall refill plug.
You are done.
Plugs are for 22 or 24 mm wrench.One at the bottom the other one at level of drive axle of the transmission.They are same size.

Jun 16, 2010 | 1995 Honda Accord

2 Answers

What are the procedures for changing primary and transmission oils on a 2000 heritge


The drain is under the crankcase. Please review the video I'm attaching. Any questions hmu. A thumbs up would be greatly appreciated if this answer is helpful to you.
2000-fxst-softail-standard-what-are-the--4d5i0utctl2htkxwobhufr12-1-0.jpg

May 20, 2010 | 2000 Harley Davidson FXST Softail Standard

1 Answer

Where is the oil drain plug on 2007 Heritage Softtail Classic and how to change oil?


Look at the bottom of the oil tank from the right side of the bike. You'll see one hose or pipe that goes downwards towards the back of the transmission. The hose will follow the frame and come out way down low on the backside of and slightly under the transmission. There is a plug in the hose or pipe. Take the plug out and the oil tank will drain.

To change the oil, drain the tank, change the oil filter, refill with three quarts of oil in the tank. You also have oil in your primary that should be changed every 5000 miles or so, and the transmission serviced at the same interval as the primary.

To drain the oil on the primary, there is a drain plug under the primary case at the very rear of the case. Remove this to drain the case. Refill the primary through the derby cover. Fill with oil until the level is just to the bottom edge of the clutch spring. 38-42 ounces of oil. Do not overfill or the clutch will drag and make finding neutral with the engine running impossible to find.

To drain the transmission, there is a small plug on the bottom side of the chrome cover on the right side of the transmission. Remove the plug, drain the tranny, and refill through the large plug that takes a hex key in the chrome cover. 20-24 ounces of transmission lube.

Good Luck
Steve

Apr 01, 2010 | 2005 Harley Davidson FLSTC - FLSTCI...

1 Answer

How do I change all my fluids on a FLHTC 2005


There are three areas that you have to service, engine oil, primary oil, and transmission.

To change the engine oil, underneath the transmission, you'll find two drain plugs. The drain plug nearest the left side of the engine is the the engine oil drain. Warm the engine a bit and drain the oil. Change the oil filter. This is a messy job so put something down to catch the oil as it runs out of the filter. Replace drain plug and refill with oil.

The plug nearest the center of the transmission is the transmission drain. Remove the plug to drain the transmission. Once drained replace the plug and refill the transmission through the transmission fill hole in the chrome cover on the right side of the transmission.

To change the primary oil, underneath the primary outer cover very near the rear of this cover is a small drain plug. It takes a Torx wrench to get the plug out. Remove the plug to drain the oil from the primary. Remove the derby cover over the clutch. Refill with oil through the derby cover hole.

Your bike probably came with H-D Syn3 oil. You can replace the oil with this or any other oil as long as it carries a rating for use in a diesel engine. Here, it must have an API code of "C", example "SJ/CG4". Four quarts of engine oil, Add three quarts of oil and check. Fill to proper level with the fourth. Your dipstick is marked with a "Full Cold" and "Full Hot" mark. Fill to "Full Cold" mark and check again after warming up the engine.

Use Syn3 in the primary or 30 weight oil, 40-44 ounces. With the bike standing nearly straight up, the fluid level should be to the bottom of the clutch spring, large black disc in the center of the clutch. It's a diaphragm type spring.


Use Syn3 in the transmission, 20-24 fluid ounces. Check with the dip stick again with the bike standing straight up.

Nov 04, 2009 | 2005 Harley Davidson FLHTC - FLHTCI...

1 Answer

How to change trans oil fxdwg


The transmission oil is drained through a plug on the bottom of the transmission. There are two plugs under the transmission. The one closest to the center is the transmission drain plug. The one closest to the left side of the bike is engine oil.

Drain the transmission and refill with 20-24 ounces of Harley-Davidson semi synthetic transmission lube or Syn3. The filler plug is on the right side transmission cover. There is a dip stick on this plug. Make sure you've got the correct amount of lube in the transmission.

If you drain the engine oil by mistake, refill with Syn3, three quarts I think. Put in three and check, it may take four quarts.

Oct 27, 2009 | Harley Davidson FXDWG Dyna Wide Glide...

2 Answers

Im changing the transmission oil 10w40. The manuel says to put in about 13ounces but the dealer told me to fill until it overflows out the filler hole. I've put in almost a full liter(canadian) and its...


The transmission fill hole is a 10 mm bolt that sticks out about 2" the run out of the hole is a 14mm bolt an 1"1/2 below that. it looks like a bolt to hold on the clutch cover.
I had the same problem till I read the service manual.
Ron W.

Jul 09, 2009 | 2003 Suzuki AN 650 Burgman

Not finding what you are looking for?
2003 Suzuki AN 400 Burgman Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...