Question about 1986 Yamaha XJ 700 X Maxim

1 Answer

Trying to find out if a part is missing in the cluch basket. toothed shaft in center wich works off the cable. does it need spring r ballbearing beetween that and the center of cluch.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 342 Answers

Yes it does need a flat bearing and washer

Posted on May 08, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Can "ol" error because by spongy floor tiles or a move?

If you've already tried putting it on a piece of 3/4" plywood, try running it with a small load. If the error persists you could have dislodged one or more of the tub suspension springs so open the top (like the hood of a car) and check the 4 springs. If the unit is old and the springs are worn they can be replaced.

May 28, 2014 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

What would cause a clutch not 2 engage on a 19988 harley sporster.put new chrome primary cover on an clutch doesn't work.

U probably just didn't adjust the cluch cable correctly after you feed it in to the notch that I clips into their is a spring and a nut used to adjust the cable tension if it's adjusted to far eat her way it can slip or not let it clutch at all leaving it stuck in gear try turning the slot screw to change tension on the basket

Apr 13, 2012 | 1993 Harley Davidson XLH Sportster 883

1 Answer

Clutch is slipping after replacing clutch plates and springs

Hello and thanks for the question.
Your CBR1000F has a hydraulic clutch and may have a problem with the hydraulic system. I assume that the cluch plates and springs were installed properly.
I would flush out the hydraulic system first with fresh fluid and make sure that the line is free of air and the lever feels smooth and strong. The master cylinder may have become corrodd and plugged up over the years. If the hydraulic system is working properly you should go back to the clutch and check for improperly installed plates or excessive wear on the clutch center or the clutch basket.

If you have a continued problem please contact me back.

Thanks and I hope that this helps.

Feb 05, 2011 | 1990 Honda CBR 1000 F

1 Answer

I have a 2001 kawasaki zr7s. My clutch is acting up. when i pull the lever in i have no clutch. i opened the case to get to the clutch, that rod thats in the middle of the clutch acts like there should be...

the "cluch push rod" should be pushed back by the cluch springs, if there was a bearing on the end it would have broken up and be laying inside the cluch case in bits! if you have taken the cluch to bits there is a thrust washer behind the cluch body and gear box shaft if you left this washer out you wont have a cluch? best bet is get a hayns service book for your bike maybe off e-bay and you will have all the info you need to fix it plus all the photos as well of all the parts

Jan 14, 2010 | 2001 kawasaki ZR-7 S

1 Answer

Washing machin cluch

Remove front panel, remove spring clip holding clutch to motor shaft then pull clutch off shaft or gently pry off if stuck.

Sep 09, 2009 | Washing Machines

1 Answer

Cuisinart Brew Central 12-cup Coffee Maker Filter Basket Anti-dripo has come unattached. We have a spring and the anti-drip puiece. How do they go together?

Hello tfsmithcambr,
You need 3 pieces. The bottom plug, the spring, and the collar. Slip the spring over the plug. Insert the plug into the basket end. Slip the collar onto the inside the basket end of the plug shaft until it clicks. Should be good to go. If this does not work or you are missing a piece, you may need a new basket. Hope this is helpful. Good luck and kind regards, NormanZ

Jul 07, 2009 | Cuisinart Brew Central 12-cup Coffee Maker

1 Answer

91 kx 250 tight clutch

are you shure you have ALL the clutch plates?? the cable is well lubed? the pushrodbearing/adjuster may be in the middle of the clutch basket cover plate. OR you have the wrong springs installed!

Jan 23, 2009 | kawasaki KX 250 Motorcycles

1 Answer

1991 KX 250 super tight clutch

sounds like your clutch springs are old they tend to get hard as they get old. but even with the good springs you cant move the shaft with your hands . take the clutches and basket out its not hard just remember how it comes apart lol

Jan 21, 2009 | 2002 Honda Civic

1 Answer

'98 Toyota Corolla 5 speed

Hi Gene,

The way that we install the box's is to remove the spyder housing....You can lever it out with a large screw driver....Another thing to check...the clutch plate....Have you fitted it onto the input shaft (spigot shaft) and tried it for size, to make sure you've been supplied with the correct replacement? Sorry if I'm asking stupid questions, but it can happen!....After you've fitted the box, refit the spyder housing, using a plank of wood and a good clout....It fits and locks in with a spring clip....

Hope that this is a help to you....

Best regards Johngee10

Aug 26, 2008 | 1998 Toyota Corolla

Not finding what you are looking for?
1986 Yamaha XJ 700 X Maxim Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts


Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers


Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides