Question about 2005 Honda VT 750 Shadow Aero

1 Answer

How to torque the clutch nut without it turning

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Honda Master
  • 1,508 Answers

Some manuals suggest making a tool from an old steel clutch plate by welding a rod to it to hold the hub. I usually use an air wrench

Posted on May 07, 2010

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
v2iper
  • 150 Answers

SOURCE: need the torques specs for the 2 nuts on the clutch on a harley

50 ft lbs and it is a left is tight nut...don't worry about adjuster nut on clutch just good ole tight will work on that one. compensating nut ( one in front) is 150 ft lbs.

Posted on Jul 25, 2009

RaidX
  • 632 Answers

SOURCE: need torque setting

8 Foot pounds of pressure its normally

Posted on Jun 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs


Not sure on a TwinCam, but the Evos were 60 ft/lbs, LEFT HAND THREAD!
Without a locking tool, you could try putting transmission in high gear, and have someone hold rear brakes while you tighten.

Jun 17, 2013 | 2003 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How do you change a 2002 Harley Road King stator?


Disconnect the battery. Drain the primary and remove the outer primay cover. Take the engine sprocket nut off, take the clutch adjuster out of the center of the clutch assembly and remove the mainshaft nut. This nut has LEFT HANDED THREADS. Remove the nut that holds the primary chain adjuster. Take the engine sprocket, clutch assembly, and primary chain off all together. Then, pull the rotor off the engine sprocket. It can be difficult to get off due to the strong magnets in it. Once off, there are four small bolts holding the stator on and two small screws holding the plug into the case. Installation is the reverse of disassembly. Torque the small Torx bolts that hold the stator on to 40 inch pounds. The engine sprocket nut torques to 150-165 foot pounds with one line of Loctite 271 heavy hold thread locker in it. The LEFT HANDED threaded mainshaft nut torques to 60-80 foot pounds with a single line of Loctite in it. You'll need a primary locking bar to keep the engine from turning while applying torque to the engine sprocket nut and the mainshaft nut.

Good Luck
Steve

Aug 15, 2011 | Harley Davidson FLHRC Road King Classic...

1 Answer

How do i replace the regulator & stator on a 92


There's nothing to replacing the regulator. It simply bolts to the frame. The wires from the regulator to the stator plug into the plug on the lower left front of the engine case. The larger longer wires runs back along the frame and up to the positive post of the battery.

There's a bit more to replacing the stator. To replace the stator, disconnect the battery and drain the primary case. Remove the outer primary cover. You'll have to take the engine compensator sprocket nut off and remove the mainshaft nut that holds the clutch assembly on. To get the clutch assembly off, remove the snap ring in the center of the clutch assembly and remove the clutch adjuster. The mainshaft nut is inside the hole in the center of the clutch assembly. The nut has LEFT HANDED THREADS. Take the nut off the primary chain adjuster and take the engine sprocket, primary chain with adjuster, and the clutch assembly off all together. The rotor is on the engine sprocket shaft. It can be difficult to get off because of the magnets inside of it. The rotor has two holes in it. I use two long bolts and put them just into the holes deep enough to hold the rotor by squeezing the ends together. Pull the rotor off. The stator is held on by four small Torx bolts and it has a wire support that is held on by two small sheet metal screws. When you install the new stator, make sure you use thread locker on the threads and torque the bolts to 40 inch pounds of torque. The sprocket shaft nut torques to 150-165 foot pounds of torque. The clutch mainshaft nut (LEFT HANDED THREADS) torques to 60-80 foot pounds. You'll probably need a locking bar or some way to prevent the engine from turning while you torque the nuts.

Good Luck
Steve

Aug 01, 2011 | Harley Davidson FXR Super Glide...

1 Answer

When I install clutch basket hub on my 1978 superglide 1200cc, I torque the nut to 50-60 ft lbs. Transmission will not turn. Seems to be in a bind. Loosened nut, transmission frees up. The manual shows no...


The inner clutch hub fits onto the tapered mainshaft of the transmission. If I understand you correctly, you are saying that when you put the inner hub on and torque the nut, it locks up and will not turn. The mainshaft has a woodruf key in it that goes into a slot in the in hub. If this key is pushed out when installing the clutch, it will become trapped between the hub and the inner primary housing locking the clutch assembly up. Sometimes getting the inner hub on without knocking this key out can be a daunting task for someone that is new at it. Take the hub back off, put the key in the mainshaft using a thick grease or something. Look into the hole in the inner hub as you install it and make sure the key is aligned with the slot.

Good Luck
Steve

Jul 21, 2011 | Harley Davidson FXD Dyna Super Glide...

1 Answer

How do i remove the clutch basket on a 1988 fxrs


Now, if you wish to remove the clutch as a unit, disconnect the battery. Drain the primary case. Remove the primary cover. Take the compensator sprocket nut off. Take the nut off the primary chain adjuster. Now, take the snap right out of the clutch release plate and remove the plate. You'll have to take the nut off the mainshaft that holds the clutch assembly on. It has LEFT HANDED THREADS. Then you need a puller to get the clutch assembly off the tapered shaft, Custom Chrome 20269, $30 and a "locking bar" to keep the engine from turning while you torque the nuts, Custom Chrome 20825,$26. You can then disassemble the clutch and you'll need a press to press the inner clutch hub out of the outer clutch hub.

Then compensator sprocket nut torques to 150-165 foot pounds and the clutch mainshaft nut torques to 60-80 foot pounds LEFT HANDED. Put one line of Loctite 271 red in each nut. You will need a torque wrench that will torque in the reverse direction. All torque wrenches won't do that.

Good Luck
Steve

Apr 13, 2011 | Harley Davidson FXR Super Glide...

1 Answer

Removal motorsprocket


I'm going to assume that you are talking about how to remove the engine sprocket from the sprocket shaft in the primary cover.

First, disconnect the battery and drain the primary. Look underneath the primary and loosen the locknut for the primary chain adjuster and loosen the primary chain by turning the screw outwards a few turns.

Then take the derby cover off the primary and remove the spring and locknut for the clutch adjustment. Remove the screws from around the primary and break it loose from the engine. Turn the clutch adjustment screw clockwise while removing the primary cover. Lay the primary cover aside.

Now, there is a plate in the center of the clutch assembly held in with a circlip. Remove the circlip. Now you'll need either an air wrench or a locking bar to lock the primary to prevent it from turning so you can get the clutch hub nut and the engine sprocket nut off. The engine nut has right hand threads and comes off normally. The clutch hub nut has LEFT HANDED THREADS and you must turn it in reverse. Once you get the two nuts off, you can usually grab the engine sprocket and the clutch assembly and lift those two units and the chain off at once. Sometimes you may need a puller to get the engine sprocket off but usually it just comes right off.

Installation is the reverse with the engine nut being torques to 150 foot pounds and the clutch hub nut torqued to 60 foot pounds left handed.

Good Luck
Steve

Mar 03, 2011 | 2000 Harley Davidson XL Sportster 883

1 Answer

Whats it take to install a clutch hub for a 1988 police bike flhpt


To install a clutch is not what I call an easy job but not an extremely difficult job either. You are going to need some special tools however.

The tools you'll need are an impact wrench, a large socket to fit the compensator nut and one to fit the mainshaft nut, a primary locking bar, torque wrenches that will torque to 150 foot pounds and 70 foot pounds in the left handed direction, and a special tool required to disassemble the clutch assembly.

First, disconnect the battery, then drain the primary and remove the outer primary cover. Use the impact wrench and appropiate socket to remove the compensator sprocket nut from the engine shaft. Remove the snap ring holding the release plate in the center of the clutch assembly and remove the LEFT HANDED THREADED mainshaft nut. Take the nut off the chain tensioner and remove the primary drive (engine sprocket, adjuster, and clutch assembly) as a unit.

Now, using the special tool, compress the clutch spring and remove the lock ring holding the clutch assembly together. Disassemble the clutch and reassemble it with the new clutch hub. Reinstall the primary drive. Apply one line of Loctite 271 inside the mainshaft nut and torque it to 70-80 foot pounds LEFT HANDED. Apply two lines of Loctite 271 (red) to the compensator nut and torque it to 150-165 foot pounds. This is what the locking bar is for, to keep the engine from turning while applying the torque to these two nut. Adjust the primary chain and reinstallt the outer primary. Add about one quart of lubricant to the primary. Reconnect the battery. Adjsut the clutch and cable.

Good Luck
Steve

Sep 17, 2010 | Harley Davidson FLHRI Road King...

1 Answer

How do I pull the front Sprocket inside the primary cover to change the stator


The compensator has a large nut on it and it's very tight. But, I get them off with an air impact wrench. You also have to remove the clutch assembly and primary chain. To remove the cluch assy, remove the clutch rod adjuster plate in the center of the clutch assembly by removing the snap ring. Inside the clutch is the mainshaft shaft nut. It has LEFT HANDED THREADS ON IT. Take it off and the remove the nut that holds the primary chain adjuster off and lift the front sprocket, the clutch, and the chain off all together.

The rotor should come right off but you'll have to put two bolts in the holes on the rotor and squeeze them together to get a grip on the rotor to pull it off. The magnitism force is quite strong.

When replacing the clutch and compensator, the mainshaft nut torques to 60-80 foot pounds of torque LEFT-HANDED. The sprocket shaft nut torques to 150-165 foot pounds. You'll need something to lock the primary chain while you torque the nuts or the engine will turn before you get them torqued.

Good Luck
Steve

Aug 06, 2010 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

Tork specs for clutch 71 sportster XL


The clutch hub nut, the large nut holding the inner and outer clutch hubs on, torques to 110-150 foot pounds. The mainshaft nut that holds the front final drive chain sprocket on torques to 35-65 foot pounds. Engine sprocket nut torques to 150-165 foot pounds. Use two lines of Loctite 271 (high strength, red) on the sprocket shaft. The six small 1/4" nuts that go on the outside of the clutch have no torque specs. The manual says to "tighten nuts until releasing disc bottoms on spacers". Torque them like you would any other 1/4" nut, about 10-14 foot pounds. They should be nylock or self locking type nuts. If not, you can use a drop of Loctite 242 (medium strength,blue) on each threaded stud.

Dec 12, 2009 | 1979 Harley Davidson XLS 1000

1 Answer

Need the torque specs on clutch for a 85 FLHTC


The torque specs are the same as with any Evolution engine. The compensator sprocket 150-165 foot pounds.
Clutch hub nut (left handed threads) 60-80 foot pounds.

Use Loctite 271 on threads. Two lines in nut on Compensator and one line in clutch hub nut.

Jul 27, 2009 | Harley Davidson FLHTC - FLHTCI Electra...

Not finding what you are looking for?
2005 Honda VT 750 Shadow Aero Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...