Question about 2002 Yamaha TDM 900

2 Answers

How do you get to the battery to connectsomething

How do you get to the battery to connect something to it, do you have to remove the tank.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

The battery is under the seat. No need to remove the tank.

Posted on Sep 29, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 126 Answers

While I have never seen this particular model, Yamaha tends to keep the batteries behind the tank under the seat or rarely behind a side panel. Access should not take more than a minute or so.

Posted on May 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When draining a fuel tank do the drain us need to be replaced or can you reuse the same one


Feul tanks do not come with a drain plug. The only way to drain a fuel tank today is to remove it. Removing a fuel tank is a dangerous thing if you do not know all the safety procedures.

Fire extinguisher on hand rated for a fuel type of Fire.

No open flames, and a well ventilated area.

Jack and jack stand And chocks to prevent vehicle from moving.

Brass punch for removing tank locking ring no sparks.

Additional blocks to be placed on jack to hold tank.

An extra person to help in lowering the tank.

Pliers to remove hoses and ground connection.

New fuel rated hose and hose clamps.

Something to stop fuel from leaking back out if hose, something to catch fuel.

A new set of straps and straps protection from rubbing tank.

You will have to remove gas cap and any type of connection that will hinder the removal of tank.

To replace is just a reversal of removal.

Mar 05, 2015 | Cars & Trucks

1 Answer

How to remove tank from 2010 softail FLSTC


Drain the gast tank. Remove the chrome bolt holding the dash to the tank. Lift up the dash and disconnect all the electrical connections. Remove the dash. Remove the seat. Remove the bolt at the bottom tank mount. Remove the nut and bolt at the bottom front of the tank. Disconnect the gas line on the left side bottom of tank. If the tank has a crossover line at the front, disconnect it. Lift the rear of the tank and block it up with piece of wood or something similar. Disconnect the electrical connection for the gas gauge under the left side of the tank. Remove the tank. Installation is reverse of removal. Don't forget to reconnect the fuel gauge and gas line, and crossover, if equipped. Good luck!

Nov 08, 2012 | Harley Davidson FLSTC - FLSTCI Heritage...

2 Answers

How do I get to the battery on 2008 Yamaha FZ6s


for your solution you should ask your nearest same product retailer or wholesaler if not you satisfied then contact to service center related your yamaha FZ6s battery.

Aug 17, 2012 | Yamaha FZ6 Motorcycles

2 Answers

Removal of gas tank


Fuel Tank Assembly Removal & Installation Single Tank To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Relieve fuel system pressure (See: Fuel System Relieving)
  3. Disconnect the negative battery cable
  4. Raise and support the vehicle
  5. Drain the fuel tank in an approved container
  6. Remove or disconnect the following:
    • evaporative emission (EVAP) canister Disconnect fuel lines for single tank gm_trk_sub15_fuel_line_rem_singl_tnk.gif

    • Chassis fuel lines (B) at the fuel tank (A)
      1. Cap the fuel and EVAP lines to prevent possible fuel system contamination
      Disconnect EVAP vent line gm_trk_sub15_evap_vent_line_rem.gif

    • EVAP vent line at the fuel tank clip (E) Disconnect vent hose and filler hose gm_trk_sub15_vent_filler_hoses.gif

    • Vent hose and filler hose clamp (D, B)
    • Vent hose and filler hose from the line
    Fuel tank removal gm_trk_sub15_fuel_tank_rem.gif

  7. With the aid of an assistant or a suitable jack support the fuel tank
  8. Remove or disconnect the following:
    • Fuel tank strap attaching bolts
    • Fuel tank straps
  9. Carefully lower the rear of the fuel tank slightly
  10. Remove or disconnect the following:
    • Fuel sender cover Fuel tank connections gm_trk_sub15_fuel_tank_conn.gif

    • Fuel sender and the fuel pressure sensor electrical connectors
    • Fuel tank
  11. Place the fuel tank in a suitable work area Fuel lines at the tank gm_trk_sub15_fuel_lines_at_tank.gif

  12. Remove or disconnect the following:
    • Fuel feed and return lines (C) from the fuel sender and the retaining clips
    • Fuel pump assembly from the fuel tank
    • EVAP line from the fuel tank roll over valves (B, D) and the retaining clips (A)
    • Fuel fill hose and the vent hose from the fuel tank
    • Fuel tank
To Install:
  1. Install or connect the following:
    • EVAP line to the fuel tank roll over valves and the retaining clips
    • Fuel pump assembly to the fuel tank
    • Fuel feed and return lines to the fuel sender and the retaining clips
    • Fuel fill hose and the vent hose to the fuel tank; torque hose clamps,
      1. Torque to: 22 lb-in. (2.5 Nm)
  2. With the aid of an assistant or a suitable jack support and partially raise the fuel tank front end first
  3. Install or connect the following:
    • Fuel sender and the fuel pressure sensor electrical connectors
    • Fuel sender cover
  4. Fully raise the fuel tank
  5. Install or connect the following:
    • Fuel tank straps
    • Install the fuel tank strap attaching bolts;
      1. Torque to 30 lb-ft. (40 Nm)
    • Fuel fill hose and the vent hose to the lines;
      1. Torque hose clamp to 22 lb-in. (2.5 Nm)
  6. Torque the vent hose clamp,
    • Torque to: 22 lb-in. (2.5 Nm)
  7. Connect the EVAP vent line to the fuel tank clip
  8. Remove the caps from the fuel and EVAP lines
  9. Install or connect the following:
    • chassis fuel lines at the fuel tank
    • EVAP canister
  10. Lower the vehicle to the ground
  11. Fill the fuel tank with clean fuel
  12. Install the fuel filler cap
  13. Connect the negative battery cable
  14. Use the following procedure to inspect for leaks:
    • Turn the ignition on for two seconds
    • Turn the ignition off for 10 seconds
    • Turn the ignition on
    • Inspect for fuel leaks
  15. Install the engine sight shield
  16. Road test the vehicle to check performance

Feb 12, 2011 | 2000 GMC Sierra

1 Answer

Can fuel pump be put in without dropping the tank.


Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Oct 09, 2010 | 1999 GMC Jimmy

1 Answer

Instructions on how to remove fuel pump for 95 chevy blazer 4x4


Removal & Installation
To Remove:


  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:

    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top
      of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device

To Install:


  1. Install or connect the following:

    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame

      1. Torque to: 33 ft. lbs. (45 Nm)

    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable

  2. Refill the tank.
  3. Run the engine and check for leaks.






View of the in-tank fuel pump assembly.
7924jg21.gif




prev.gif next.gif

Sep 23, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

How to put hi pressure fuel pump into the engine,it does not have any mark on the pump rotor?


prev.gif next.gif Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Jul 15, 2010 | 2004 Chevrolet Blazer

3 Answers

How do you change a fuel pump and filter on a 2005 manual chevy aveo?


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat.
  4. Remove the fuel pump access cover.
  5. Disconnect the electrical connector at the fuel pump assembly.
  6. Disconnect the fuel line.
  7. Remove the fuel pump assembly clip.
  8. Remove the fuel pump assembly from the tank.
  9. Remove and discard the gasket.

To install:
  1. Clean the gasket mating surface on the fuel tank.
  2. Position the new gasket in place.
  3. Install the fuel pump into the fuel tank in the same location as removed for ease of line and connector installation.
  4. Install the fuel pump assembly clip.
  5. Connect the fuel pump assembly connector.
  6. Install the fuel pump line.
  7. Install the fuel pump access cover.
  8. Install the EF10 fuse.
  9. Connect the negative battery cable.
  10. Perform an operational check of the fuel pump.
  11. Install the rear seat.

Mar 06, 2010 | 2005 Chevrolet Aveo

1 Answer

HOW TO TAKE A FUEL PUMP OUT A 2001 ISUZU TROOPER


REMOVAL PROCEDURE

  1. Disconnect the negative battery cable.
  2. Drain all the fuel from the tank.
  3. Install and tighten the drain plug. Tighten Tighten the drain plug to 20 N.m (14 lb ft.) .
  4. Remove the fuel tank.
  5. Remove the retaining screws from the fuel tank.
  6. Remove the fuel pump assembly from the fuel tank.
    1. Cover the fuel pump opening in order to prevent dust, dirt, or debris from entering the fuel tank.
    INSTALLATION PROCEDURE

    1. Install the fuel pump assembly. Tighten Tighten the fuel pump assembly mounting bolts to 3 N.m (27 lb ft.) .
    2. Install the fuel pump assembly retaining screws.
    3. Install the fuel tank assembly.
    4. Fill the tank with fuel.
    5. Tighten the fuel filler cap.
      1. Connect the negative battery cable.
      REMOVAL PROCEDURE # 2
      REMOVAL

      CAUTION: When repair to the fuel system has been completed, start engine and check the fuel system for loose connection or leakage. For the fuel system diagnosis, see Computers and Control Systems/System Diagnosis.

      1. Disconnect battery ground cable.
      2. Loosen fuel filler cap.
      3. Drain fuel. Tighten drain plug to the specified torque after draining fuel. Torque: 20 N.m (14 lb ft) - M8
      4. Remove fuel tank assembly (1).
      5. Remove fuel pump (FP) assembly (2) fixing screws and remove the FP assembly.
      NOTE: After removing FP, cover fuel tank to prevent any dust entering.
      INSTALLATION
      1. Install FP assembly (2).
      2. Install fuel tank assembly (1).
      3. Fill the tank with fuel and tighten fuel filler cap.
      4. Connect battery ground cable.

Oct 18, 2009 | 2001 Isuzu Trooper

1 Answer

HOW DO I REPLACE THE FUEL PUMP ON 2003 CHEVY S10 PICK UP


Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
1e2538e.gif

Jun 26, 2009 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
2002 Yamaha TDM 900 Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...