Question about 2005 KTM SX 525 Racing

1 Answer

My bike wont go into 1st gear without dieing it runs fine except for that and tried bleeding the clutch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • KTM Master
  • 1,508 Answers

Assuming there is nothing major wrong with the clutch and you have pressure at the lever.
The plates can stick together sometimes, if you can push start it, ride it with the clutch all the way in and vary the throttle, this can seperate the plates and it will work normal, change the oil after the ride and make sure it is motorcycle oil, as car oils will cause the opposite problem and cause clutch slip.

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1981 yamaha exciter 185 dies when i put it in gear i've already tried adjusting clutch still dies. was running fine for prior 3 months


The bike will either have a side stand cut out switch or a clutch cut out switch.

Both these will make the bike die when the side stand is down or the clutch is not pulled in

Sep 23, 2014 | 2001 Yamaha SR 125

1 Answer

Why wont my 1988 ford f150 4 speed go in gear?


alpst sounds like your clutch disc is in backwards, DO you have a good strong clutch pedal feel?

Sep 10, 2014 | Cars & Trucks

2 Answers

Problem with 2001 jetta 1st gear


Hi. Does it go into 1st without the engine running? If not then you have a problem with the likages. If it does then check the clutch.

Jun 12, 2014 | 1997 Volkswagen Jetta

1 Answer

I have a 92 fzr 600 when i engage my clutch amd shift into first it dies like the clutch isnt engaged. i checked the clutch cable and it seems to be working fine


With the engine not running can you select 1st gear pull in the clutch lever and push the bike with no difficulty, if you cant, it may be the clutch plates have become stuck together, this can occure from standing for long periods, if you can push the bike it may be the neutrol safety switch, or the side stand safety switch have become faulty, and cutting the bike out as a precaution

Jul 25, 2011 | 1992 Yamaha FZR 600

1 Answer

With the motor off and 1st gear ingaged when you


This may be off the wall ... clutches do wear and need adjustment ... your bike is almost 30 years old ... has it been serviced recently? Might be worth a trip to the Yamaha Shop.

May 16, 2010 | 1982 Yamaha XJ 650

1 Answer

Started bike, pulled clutch lever, put bike in 1st gear, let out on clutch and nothing happened. clutch lever moves freely with no tension at all. when i put the kickstand down it shuts off like its...


The clutch lever should have some tension, so could be a problem with the hydraulic actuator stuck, or a failure of the clutch. try bleeding the clutch, or pull the clutch cover off and see if the pressure plate moves

Apr 22, 2010 | Yamaha YZF-R1 Motorcycles

3 Answers

I bought my wife a 1984 Honda VT750 for her 1st bike however the problem we have is that it is difficult to go into 1st gear. Sounds like its grinding when you try to go to 1st gear unless you use a little...


Now you know why the prior owner sold the bike. The problem is a bent shift fork. The engine comes out of the bike then the bottom end gets disassembled to a point where a new shift fork can be installed. The "grinding" is the dogs on the slider gear not fully engaging into first gear.
Your local Honda dealer will charge you $1000 to $1500 to do the repair. Sorry to be the bearer of bad news. Please rate my answer. Thanks!
b641f62.gif

Nov 14, 2009 | Honda VT 750 Shadow Motorcycles

1 Answer

1982 Honda 650 nighthawk; jumps and stalls when put into gear.


this may help,it doesnt sound like the clutch is out of adjustment,it sounds like the clutch plates have become stuck together,(this happens quite a bit if the bike has been parked for a while..ie over winter)..to fix it get the bike moving,down a drive way or something..then just bang it into gear,then shift into the highest gear you can by shifting without the clutch,once you have a bit of pace on simply hold the clutch lever in and work the throttle on and off all the while holding the clutch lever in,the clutch should free itself fairly quickly and should be back to normall,a lot of older bikes are good at doing this..hope this helps

Jul 05, 2009 | 1983 Yamaha XJ 650

1 Answer

1100 wierd clutch disengage problem


Bleed your slave cylinder on the sprocket cover and refill the hydraulic fluid. If you have any leaks you will get air in the system and it will not fully disengage the clutch. As for the 750, they have cable clutches and you just need to adjust the slack of the cable.

Nov 20, 2008 | 1992 Suzuki GSX 1100 GN

Not finding what you are looking for?
2005 KTM SX 525 Racing Logo

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...