Question about 2004 Harley Davidson FXDL - FXDLI Dyna Low Rider

1 Answer

How do I remove the signal light bolt? It is getting caught on the tire.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

The easiest way is jack the rear wheel up off the ground. If this doesn't work, you can remove the lower bolts from the shockes but watch out for how high you raise the bike. You can bust a belt if not careful and you DON"T want to do that. Lots of money and a big job to repair.

Posted on May 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the exact process for removing a flat tire on troy-bilt snowblower, model 8526?


Yes you need to prevent the wheel from turning. This the same process as removing the bolt from MTD mowers. You can also use a small impact wrench to remove the bolt. These are normal RH threaded bolts.

Be aware that after you remove the bolt you may still not be able remove tire assembly if it has rusted on to shaft.

Feb 15, 2015 | Garden

1 Answer

Changing headlight bulb


remove 7mm bolts holding hd light , remove the five 10mm bolts,two clips and two philips hd screws on cover between hd light . then on bottom in front of front tire remove all plastic tabs and screws on wheel well lining . now you can get to a single 10mm bolt holding the hd light. hd light is ready to be removed.

Jul 12, 2013 | 2008 Saturn Aura

1 Answer

How to remove rear fender?


Remove the seat. Unplug the connector for the taillight and rear turn signals. Stabiliize the bike and remove the upper shock bolts. The job is also easier if you remove the rear tire. Remove the bolts from the fender struts on both sides. Be sure to hold the fender or clamp it place when removing the bolts so the fender doesn't slip out of place and get scratched. Unplug the turn signals from the taillight housing. Pull the wires and connectors through the holes in the struts. Lift the fender out.

Aug 10, 2012 | 2000 Harley Davidson XL 1200 S Sportster...

1 Answer

2007 Dodge Magnum, RT/AWD - Front Driver side wheel area noise, like snow/ice was caught up under, checked notheing. One month later the noise came back but with a vengence. Now makes the noise at all...


Check the Brakes first. Are the pads worn down to metal. Is the Caliper Stuck (open)?
Raise and Support the Front and Rear (because of AWD) of the vehicle.
Remove the left front tire. Make sure the Parking Brake is engaged. Place the lug nuts back on the lug studs. Place the Vehicle in Neutral. Turn the wheel (without the tire on) and listen for where the noise is coming from. A bad bearing will feel rough (not smooth) and sound 'crackly' when trying to turn the one wheel. Make sure it is not from the CVJ.
If not smooth: Remove and Replace the wheel bearing. And yes you can do it yourself saving you about $150-$200 dollars. It is a bolt-on (4 bolts) bearing. Bolt Heads should be on the back side of the steering knuckle.
Remove the Brake Caliper, Caliper Brace, and Rotor.
Remove the 4-bolts (turn the wheels left and right to better access these bolt heads) and slip the bearing off the Axle. You may have to hit the bearing to loosen it.

Jan 05, 2010 | 2007 Dodge Magnum SRT8 Wagon

1 Answer

HOW DO YOU REMOVE THE HEADLIGHT ASSY TO REPLACE THE TURN SIGNAL BULB


SECTION 417-01: Exterior Lighting 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Side Lamp/Front Turn Signal Lamp Bulb Removal and Installation
  1. Remove the wheel and tire. For additional information, refer to Section 204-04 .
  1. Position the inner fender well aside.
    1. Remove the bolts.
    1. Remove the pin-type retainers.
    1. Remove the screw.
    1. Position the inner fender well aside.
  2. Remove the lamp socket from the lamp assembly.
  3. Remove the bulb.

06a0ca1.gif

Dec 01, 2009 | 2001 Ford Escape

1 Answer

I have a left front clearance light out how do you get it out 1


Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
  1. Disconnect the negative battery cable.
  2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
  3. Remove the bulb from the socket; if necessary, replace the bulb.
  4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
  5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
Fig. 1: Common front turn signal/parking light mounting

d16c14b.jpg
Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

8b774bd.jpg
Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

09f4811.jpg

Jul 24, 2009 | 1992 GMC Sonoma

1 Answer

In order to remove the front tire on my crf150f do i just remove the 17mm bolt or what


yes take off the vavle stem bolt and the rim lock bolt (the 17mm) then get some tire irons and get to work

Jul 18, 2009 | 2003 Honda CRF 150 F

1 Answer

Wheel broke of my Power Chair


I assume you are referring to the caster tire, not the drive tire. You will need to check to see if the rim is a split-rim or a solid rim. A split-rim will have 4 or more bolts holding the two halves of the rim together. If you have flat-free tires i.e., foam-filled solid tires, evidenced by the lack of a valve stem which is used to inflate non-flat-free tires (pneumatic), you would remove the wheel from the caster by rermoving the center bolt acting as the axle. Then remove the bolts holding the rims together. Reposition tire on top of one of the rim halves, then place the other rim half on top so that the bolt holes in the top one line up with the holes in the bottom one. You need to buy a couple of bolts that are about 3/4 in or more longer than the bolts that you removed, as you now must press the two halves back together and the stock bolts probably won't reach through. Put the two longer bolts in opposite of each other in two holes and tighten down. When the rims are pressed together, then put the stock bolts in, remove the two longer ones and replace with stock bolts. Place wheel back on the caster. If you have pneumatic tires (requiring air), make sure to always deflate the tire completely before attempting to loosen the bolts holding the rim-halves together. The same process is used for drive tire replacement. If the rims are not split rims, then it is easiest to buy an entire new wheel and tire as getting it back on is quite a chore requiring a press and lots of tequila! It's easy to break the rims. Good luck.

Jul 15, 2009 | Invacare Pronto M51 Power Wheelchair

1 Answer

Removal of front bumber passat


you have to take off head lights and signals because there is a bumper bolts behind them ,remove engine shield underneed and front tires splash shileds front side bolts ,take off front grill there is a bolts forr bumper too.
and you may need the get your a/c refrigrant **** with recycling machine because condenser and radiator come out togethar so you have to disconnect a/c lines from the condenser to take out radiator. good luck!!
Your car is may overheats for diffrent reason just make sure problem is the radiator or thermostat if its not you still gonna have same problem after at all.

Jun 24, 2009 | 1999 Volkswagen Passat

2 Answers

1998 hd 1200 sportster turn signal quit working


check the wiring under the rear tire. you probably tore the wires. if that's fine. do your flasher work? if they do then double check the bulbs. if they're fine them it could be the tsm ( turn signal module ) Only consider replacing that if the wiring is fine and the turn signals worked fine before

Jun 23, 2009 | 2000 Harley Davidson XL 1200 C Sportster...

Not finding what you are looking for?
2004 Harley Davidson FXDL - FXDLI Dyna Low Rider Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...