Question about 2003 kawasaki KX 250

1 Answer

It wont idel - 2003 kawasaki KX 250

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 338 Answers

I don't know you mechanical ability if you already tried setting the idle screw and it does not work i suggest you clean of have the carburetor cleaned problem usually is the low speed jet is clogged.
I suggest you have a mechanic take care of this problem.
there could be other problems bad crank seal or worn main bearing.

Posted on May 06, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Idels fine when cold if I run it about 5 miles it starts to miss end wont idel then dies

Check the ECT coolant sensor for sticking in a false low range letting engine run rich when warm. Check for vacuum leaks also.

Nov 06, 2015 | Cars & Trucks

1 Answer

Will only ldel when not moveing700rpms onceyou start moveing engin idels up to 1400rpms wont idel back down to 700rpms untill vehicle stops moveing why?

More info would help, but I'd say you have a throttle or its cable or linkage to the fuel throttle body sticking. If you are a DYI you should get a repair manual from your local auto parts store. You will probably need it next time.

Oct 09, 2015 | Cars & Trucks

1 Answer

My loncin 50cc dirt bike takes a long time to warm up and I don't know whats wrong with it and where's the idle on it?

that is the idel screw that you were pionting at.
can you get a better picture of were he popping is coming from?
Sounds to me that you have a head gasket leaking and if the head gasket is leaking the bike wont idel.

Oct 11, 2012 | Motorcycles

1 Answer

2007 yzf600r bike wont idel right at low end fine at 3000 rpms and tach jumps from nothing up to 8000rpms at idel sounds like a coil cuting out not sure took carbs apart no dirt and were nice and clean...

Tach jumping from 0 to 8k rpm is usually a disconnected fuel sender plug. Check your spark plug coil/caps for arcing through the rubber insulators midway up the coil/cap.

Jun 20, 2010 | Motorcycles

1 Answer

1989 200hp evirude wont idle in water idels fine out of the water

I would readjust your idle mixture screw with engine in gear and on the water at an idle. That is a common problem after rebuilding carbs. It will run diferently under a load in the water. Just tie up to the dock and adjust them there.

Jul 11, 2009 | Boating

1 Answer

Run;s hot while driveing. Does not while ideling.

one test to do, on the spot rev the car at 3000rpm, if it overheats you have a radiator probem, blocked etc, if it still wont overheat and will only overheat while driving then water pump the problem, its not pushing enough water under load, i would advise check radiator first.

May 12, 2009 | 1997 Nissan Maxima

Not finding what you are looking for?
2003 kawasaki KX 250 Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides