Question about 2002 Buell X1 lightning

1 Answer

My x1 has no spark to front cylinder,changed wires,plugs,coil,all check good...scratching my head...think perhaps broken wire...if not then ignition control....

Posted by on

  • hhss2 May 11, 2010

    Here is your solution » Honda »
    Suzuki » Yamaha » kawasaki » Others a

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Buell Master
  • 40,013 Answers

Hi, Aecilak if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue and free downloads that you will need please visit the websites below, and for specific information or questions, please feel free to contact me at xlch@mail.com. Good luck and have a nice day.
http://www.buellxb.com/forum/showthread.php?10788-Need-help-no-spark
2000 buell x1 wont crank no spark
http://buellmods.com/content/downloads/manuals/x1lightning/2002_x1_manual.pdf
TWIN Motorcycles Buell parts
http://www.ukbeg.com/pash/2008%20Buell%20XB/99493-08Y.pdf

Posted on Jan 18, 2016

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rselvy
  • 83 Answers

SOURCE: Rear cylinder not firing

The first thing I would do is replace the spark plugs again. You can foul a plug and it will cause you more problems than you can ever imagine. I see you have done all the logical things that I would recommend but I did not see you have replaced the plugs after the 200 miles. You would be surprised at how many times a $2.00 part can cause fits beyond belief.

Posted on Dec 08, 2008

pugwash814
  • 377 Answers

SOURCE: im not sure how to replace my starter relay on my

. The relay is attached to relay connector located to the right of
the battery underneath the seat.
Pull relay from relay block.
. Connect positive battery lead to the 86 terminal.
. Connect negative battery lead to the 85 terminal to
energize relay.
. Check for continuity between the 30 and 87 terminals.
A good relay shows continuity (continuity tester
lamp “on” or a zero ohm reading on the ohmmeter).

Posted on Nov 07, 2009

  • 6 Answers

SOURCE: 1999 x1 lightning 118/250 runs on 1 cylinder

I have a 99 X1 #170/250 it does same thing when its cold. I put the buell race module still does it took it in and had motor turn apart and found nothing bike runs great when its warm you need to let it warm up it should start to fire

Posted on Mar 05, 2010

ruthlesswhit
  • 47 Answers

SOURCE: 2001 buell cyclone m2...new coil pack and wires still no spark

Check the starter interlock relay. Check the pickup under the timer cover. Check all fuses and diodes.

Posted on May 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coil not firing on one side harley road king


Hi Anonymous, on twin cams make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Battery voltage below 8.7 volts, loose or broken battery cables especially ground cable to frame.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, MAP or BAS sensor.
7. Faulty ignition switch.
Good luck

Feb 02, 2014 | Harley Davidson Motorcycles

1 Answer

Rear cylinder not firing


Carb or fuel injection? Spark or no spark? Check for spark by putting a new plug into lead and laying on cylinder head. Leave old plug in engine. Start bike. If carb and no spark then plug or coil would be first suspects, then ignition module, then wiring from coil to ignition module. This is assuming you have compression on rear cylinder and all mechanical checks completed. If fuel injection and good spark, then ECU most common problem. Then injector, then wiring. If no spark, check coil, then wiring frpm coil to ECU, then ECU.

Nov 10, 2013 | 2000 Harley Davidson FXSTB Night Train

1 Answer

Ignition coil wire diagram


Hi, Anonymous if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue, please visit the websites below. Good luck and have a nice day.
1986 K75 Has No Spark BMW com
Damn bike won start BMW K75 K100 K1 K1100
https://www.tradebit.com/filesharing.php/search/0/1986+bmw+k75c
BMW Motorcycle Parts Fiche OEM BMW Motorcycle Parts online 1970 present BMW
http://www.bmw-motorrad.com/us/en/index.html?content=http://www.bmw-motorrad.com/us/en/services/manuals/manuals_main.html¬rack=1

Sep 20, 2013 | BMW Motorcycles

1 Answer

2009 electra Glide Classic rear cylinder doesn't spark its not the coil or wire


Hi D, if you have a CKP sensor it needs compression to send correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Battery voltage below 8.7 volts, loose or broken battery cables especially "GROUND" cable to frame.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, MAP or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm.
For a prime suspect please visit the website below. Good luck and have nice day. Harley Diagnostic Codes 04 to Present

May 24, 2012 | 2009 Harley Davidson FLHTC Electra Glide...

1 Answer

I have no spark on top cylinder of my 97 rs 250,the coil is ok, plug is ok any ideas?


Hi, Anonymous if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue, please visit the websites below. Good luck and have a nice day.
DOWNLOAD 1997 Aprilia Rs 250

Mar 31, 2012 | Aprilia RS 250 Motorcycles

1 Answer

How to change spark plugs in a 2005 chev colorado


SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

1 Answer

I tried using quick start on it, but all that did was make it sputter a bit, so I am assuming that the fuel is not reaching the cylinders, anyone have any ideas?


1) Check for spark remove one of the plugs, connect the plug wire to it and ground spark plug base to a good ground , such as the cylinder head , position the plug so you can see the electrodes , crank the engine over , a fat blue spark should be evident. 2)If the spark is good , check for one or more of the following possible malfunctions 1) Obstructed fuel line or filter.2) leaking head gasket(s)3) low compression. If the spark is not good, check one or more of the following a) Weak ignition coil(s) b) Weak CDI unit. c)Loose electrical connections. d) Dirty electrical connections. e)Loose or broken ignition coil ground wire. f) Broken or shorted high tension lead to the spark plug. Difficulty in starting. Check for fouled spark plugs, Improperly adjusted choke, contaminated fuel system, improperly adjusted carburetor,weak ignition unit,weak ignition coil (s), poor compression

Feb 05, 2011 | 1980 Yamaha XJ 650

1 Answer

I am having troubles with my 1999 Monte Carlo, it's seems smogged down, all of the exhaust system checked out good, I pull #3 and #6 spark plug wires off with the car running, no change, but coil checked...


I would be doing a compression test , could be burnt valves or a broken camshaft . I have seen the V6 3.8l Buick engines snap camshafts just in front of the 2 rear cylinders this causes the front 4 cylinders to work perfect but the back 2 do nothing at all.
Do the compression test and let me know what your readings are ......
Hope this helps

Jul 08, 2009 | 1999 Chevrolet Monte Carlo

1 Answer

2000 chrysler concorde no spark on #2 cylinder


If it ran good prior to spark plug replacement, then yes, I'd be looking real close at the plug wire to that particular spark plug. Perhaps it pulled apart inside boot upon removal. It may even be an indication that they are all getting weak, and time to think about a new set if it's originals.

Mar 22, 2009 | 2000 Chrysler LHS

Not finding what you are looking for?
2002 Buell X1 lightning Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buell Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

jmcpoyle

Level 1 Expert

8 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Are you a Buell Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...