Question about 2005 Husqvarna WR 125

1 Answer

Need to fix clutch spring

Got the spring on just cnt put the clip which goes under neath on how do i take the the cluth out without taking the whole engine apart

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 632 Answers

Remove Rightside crank case and remove pressure plate for clutch and thats your clutch

Posted on Jun 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Harley sportster clutch 94 1200


Do you mean the "Diaphragm Clutch Spring"?

http://img.jpcycles.com/product/630-257_A.jpg

If so, it goes like the picture, conVEX side out (high part in center facing out).

Mar 04, 2014 | Motorcycles

1 Answer

The washer shakes like craszey when it spins on the rince cycle.it dances and moves all over the place. under neath the drum there are three long pins out of place. if i put them back and put the cotter in...


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

If you look at the section on "Machine Base Parts" you'll see a number of springs and vibration pads.

It's possible that one or more of the springs or pads has come loose or broken.

In order to get to them you have to remove the cabinet.

Here is a description of how to do it.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=90fdc122f6335c7c64f46f2ea1b1c887


Also see the Whirlpool Service Manual for top load washers. It has a troubleshooting section that describes the reasons for excessive walking or vibration.

WHIRLPOOL INST AND MAINTENANCE INCLUDING HOW TRANSMISSION WORKS

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


WHIRLPOOL TRANSMISSION DESCRIPTION AND SPRINGS

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/2550f737b3129b0c85256b0600504738/$FILE/787772%20%234.pdf


If it's not the springs or pads, you may consider that the "Agitator Cams" in the transmission are not raising the Agitator Gear high enough (about 1/16" ) when the washer goes into spin mode.

See the description of what the Cams do in the Service Manual.

We had the same problem, excessive vibration and noise during the spin cycle.

In order to solve that problem, :

Assuming that you know how to remove the cabinet, agitator (you don't need to remove the tub), pump, motor and transmission the agitator cam and follower use the same whirlpool part number 62580/01. This is a plastic set used to raise the agitate gear on the shaft.

Pull the transmission.

Remove the clutch (the spring holding the clutch to the spin pinion is a bear to replace.

Remove the 8 transmission screws carefully, the transmission is full (15 oz.) of 80-90 weight oil.

Remove the transmission cover.

Pull off the spin pinion.

Push down on the agitate spring and remove the spring clip. Note where is attaches to the main shaft.

The two plastic agitate cam parts pull right off. Don't lose the washer on top of the cams.

Replace the cams, washer, spring and clip, pinion, oil (assuming you drained the oil first), cover and clutch parts.

Line up the transmission so that the release cam on the brake drum will snap onto the clutch spring retaining clip and put all parts back in the washer.

The basic tools are screwdriver, small socket set with up to a 1/2" socket, vice grips or good pliers (to remove and replace clips)

It sounds a bit complicated but it really isn't too bad and (For a $15 part, saved buying a $170 transmission.)

Following is the Whirlpool parts list for their commercial washers although the consumer models use the same part numbers.

http://shared.whirlpoolcorp.com/assets/pdfs/literature/Repair%20Part%20List%20-%20W10114743.pdf

Feb 08, 2011 | Kenmore 15864/15862 Top Load Washer

1 Answer

Why does my yz 80 1993 stall when im not moving and i put it in gear, (the bike has to be rolling to be pust in gear)


Your clutch is grabbing, adjust the cable so that it pulls harder on the clutch. If this does not help you may need to take the cluth out and inspect it for bad springs or damage

Nov 18, 2010 | 2003 Yamaha YZ 125

2 Answers

How do you change headlight on 2001 mitsubishi galant


Your bulb is held on by a spring clip that goes around the base of the bulb. The plug on the back is hard to remove because you do not want to pull too hard and damage the spring clip. Using a trouble light or flash light to see, grab the rubber tab and peel the rubber cover back far enough to see the spring. Now locate tab on the end of the spring that is under neath the catch and slide the spring off the catch. Now you can pull the bulb out of the housing and get a good grip on it to pull the wire plug off the back.Grab the new bulb by the base being careful not to touch the glass of the bulb. Do Not Get Any Grease or Dirt on the Bulb. Place the bulb in the headlight, reattach the spring clip, put on the rubber cover, and plug in the wire harness. If you do get the bulb dirty or touch it by accident just wash it with some clean drying alcohol before installation.

Aug 05, 2010 | 2001 Mitsubishi Galant

1 Answer

Toque spec for clutch springs


You can play an adjustment with your spring,the best adjustment is when your bike does't have a running cluth situation, and once you press the cluth lever and release it you'll have power just like jumping .and thats it.

May 26, 2010 | 2001 kawasaki KMX 125

1 Answer

After traveling about 8km my car wont go into 1st or reverse gear. when it is cold it goes into all the gears fine. when i switch the car off it will go into gear. we did put a new(aftermarket clutch) in a...


Cluth cable ajustment if equiped.Some cars have a cluth cylender if your model has the cylender no ajustment is available.If you had your cluth changed at a garage you might consider takeing it back in for ajustments.If you changed the clutch check cluth cable for ajustment if your car is equiped with cable if not i would perhaps remove the transmission and inspect clutch for loose clutch plate or release bearing might not be seated properly hope this helped you.

Dec 24, 2009 | Mazda 323 Cars & Trucks

2 Answers

Suzuki gsx600f clutch problem


if it is in gear for sure and it doesnt move even with the clutch engaged maybe you are missing a piece inside the clutch like the clutch boss spring. or possibly your plates are worn so much they wont hook up. or you are using a very poor grade of oil. Dont take my absolute word for all these solutions but these may lead to some problems like that.

Aug 16, 2009 | 1991 Suzuki GSX 600 F (Katana)

2 Answers

1987 kx125 clutch wont engage


push rod bent ? too short ?

Aug 06, 2009 | 2003 kawasaki KX 125

2 Answers

The bike starts fine but stalls as soon as its put in gear even without releasing the clutch


it may have a kick stand safety switch
raise the stand and and try that

Jun 25, 2009 | 2001 kawasaki KMX 125

Not finding what you are looking for?
2005 Husqvarna WR 125 Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4517 Answers

venugopal durairajan

Level 3 Expert

464 Answers

choprboz5

Level 2 Expert

196 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...