Question about 2002 Harley Davidson VRSCA V-Rod

1 Answer

Removal of Battery

I need to replace my battery could you tell me what to remove to get to it, hope you can help.

Best Regards
Alan Collins

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.


    An expert who has answered 200 questions.

  • Expert
  • 221 Answers

Lift seat up,then remove the air box decortive cover then remove air box cover remove air filter and at the base of the velocity stack are o-rings slide them up and remove the5mm screws then remove the bottom of the air box and the batttery is up front disconnect the cables and pull the rubber strape towards you and down then remove battery when replacing the velocity stacks do not over tighten the allen screws and make sure you put the o-rings back down to the base good luck

Posted on May 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need step by step instructions on removing the starter from a 1997 flstc

Disconnect the battery, remove the negative 1st...Remove primary cover...Hold pinion gear in place and remove jackshaft bolt...
Remove rear exhaust pipe...Remove allen screw end cover... Remove starter mounting alan head bolts and washers....Disconnect positive battery lead and solenoid wire from starter....Remove starter...
Note: you might need to loosen the oil tank mounts to provide clearance for starter removal...
Install new starter in reverse order...Torque specs...
Starter mounting bolts - 13 - 30 ft-lbs
Jackshaft bolt - 7 - 9 ft-lbs

Jul 17, 2011 | Harley Davidson FLSTC - FLSTCI Heritage...

1 Answer

Delonghi microwave AC 930AMQ. I have lost the manual, so could you tell me where the light bulb is situated, and can I purchase one from any electrical store. Many thanks Dawn.

Hello Dawn,

You should be able to get a replacement bulb from a number of places, however here is a message I got off the internet.

To replace the bulb would involve the removal of casing and the use of special screwdriver, thus invalidating the warranty.

Alan Hood

Sep 24, 2010 | DeLonghi Microwave Ovens

1 Answer

I'm not sure if the battery is not charging or the charger is broken because everytime I try to charge it, it charges for seconds at a time and now my camera can only take about 15 pictures even when I try...

you have to let the battery charge for 12 hres minimun, after that if you dont have power in the battery try another charger to see if it works if yes
replace the battery . or you can replace both...
try this fist....
hope that will help you
regards Alan

Jun 02, 2010 | Fuji Finepix Z20fd Digital Camera

2 Answers

The camera keeps telling me that my battery is low even when I just put some brand new ones in it. How can i fix this?

try the power connector of your battery charger to see if the cam will come on if you have one, if not; heaven if the battery are new some time they need to be charge for at least 12 hour before use...
hope that help..
regards Alan

May 14, 2010 | Canon PowerShot A700 Digital Camera

1 Answer

Change the battery on 2004 chevy venture

1st remove the positive wire from the post. Next remove the negative wire. Next remove any retainers that are holding the battery in the mount. After you free the battery, remove it from the vehicle. Reverse order of removal to replace. reset clock, and radio settings. IF your radio has an anti-theft device and it becomes active due to the absebse of power (battery removal) you may need to contact your dealer for the code to release the device. Good luck, I hope I have helped.

Apr 07, 2010 | 2004 Chevrolet Venture Passanger

2 Answers

Need to replace the starter on a 1994 Geo Prizm

starters are actually pretty easy. usually just 2 or 3 bolts holding it on. Just disconnect the battery first. Remove the bolts and the starter and then installation is reversal of removal.
Hope this helps,

Sep 15, 2009 | 1994 Geo Prizm

1 Answer

We have 3 Intermatic TB121C timers. 2 of them stopped working yesterday; the switch will no longer turn the lights on or off. We were not using the timer function at this time,just the switch. The display...

Yes, replacing the batery is each unit should get them working correctly again. The way these Intermatic timer switches work is that the battery actually operates the switching function to turn it OFF/ON. So once the battery goes dead, the switch won't operate properly.

You may have to reprogram your timer too, since some models lose their memory, once the battery goes dead. There are some new versions of Intermatic timers that use a semiconductor to hold the programming even in the event of a power loss or removal and replacement of the battery. (just an FYI for future reference).

Hope you find this Very Helpful and best regards!

Aug 12, 2009 | Intermatic Hardware & Accessories

4 Answers

Dead battery

you have to remove the 4 alan key bolt on the sides of the fairings lift the rubbers up from the rear mirrors then there are 2 small black plastics crews with little spring rivets either side of the windscreen( under the rubbers) then remove the fairing inners. then unbolt the tankwith 2 alan key bolts and the tank should have a hinge at seat end and lift the tank. this should give you access to the air box and the battery. hope this helps. from wingy

Mar 31, 2009 | 2005 Yamaha FZ6 Fazer

1 Answer

Rowe AMI R-92 Error 4


Error 4 relates to the battery on the Central Control Computer (CCC) is low.
The battery (B1 3 volts lithium) needs replacing, you will need to note all the settings on CCC so they can be inputted after the battery is replaced.

Alan Hood (ami-man)
Games Unlimited & Datex Systems
Units 4 & 5 Lion Park
New Street
S20 3GH
0114 247 0242 phone
0114 251 0727 fax

Jan 08, 2009 | Audio Players & Recorders

Not finding what you are looking for?
2002 Harley Davidson VRSCA V-Rod Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4749 Answers


Level 3 Expert

4348 Answers


Level 3 Expert

78267 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides