Question about 2004 Skyteam ST 200 OF

1 Answer

Flat front wheel

Need to remove front wheel can you advise how to ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 653 Answers

Unbolt the axle bolt, caliper bolt and axle clamp. Doing all that should release the front wheel. Good enough?

Posted on May 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can a 2006 saturn VUE 4cyl, 2.2l front wheel drive be flat towed?


if it is an automatic transmission it will need to towed with the front wheels off the ground
Short distance towing with any automatic transmission is ok but it has to be remembered that the gears/bearings will be without lubricating oil
the user manual for all automatic cars states to remove the drive shaft before towing and as that is impracticable with a front wheel drive car , best to tow with the wheels of the ground
consider putting it on a car trailer behind you MH as an alternative operation

Sep 01, 2016 | 2006 Saturn Vue 2.2

1 Answer

How do I remove the front wheels on a 99 Mitsubishi Montero Sport 3.5 liter v6 4 wheel drive


Need to explain the problem

No one driving any vehicle can't
remove a wheel if they have a flat

Nov 28, 2014 | Cars & Trucks

1 Answer

Troybilt snowblower storm 8526


Hello Max, I also have had this problem. If your wheels have two holes that are 90 degrees from each other you can remove the attaching bolt at the end of the axle. You will need to acquire a heavy duty bar type puller, two long bolts of the correct length and diameter for the holes, two nuts, and four heavy duty flat washers. You will also need some kind of drift or spacer at the end of the axle between the axle and the pressure screw of the puller. The drift or spacer needs to be smaller in diameter than the sleeve of the wheel. DO NOT press directly against the bolt hole on the end of the axle with the pressure screw. Assemble the bolts through the holes in the wheel and onto the bar puller using the flat washers and nuts Usually it takes a tremendous amount of force to break the rust connection of the wheel and axle. A high quality penetrating oil might aid in the removal. Be careful not to bend the wheel. I have also used a propane torch to heat up the sleeve on the wheel. CAUTION should be advised not to get the axle shaft too HOT. Too much heat could destroy the axle seal and/or axle bearing. Some wheels would not come off no matter what I did. In those cases, I left the wheel on the axle and removed the tire and/or tube for repair.

Feb 10, 2014 | Garden

1 Answer

Replacement instruction and diagram on a front wheel bearing for a pontic vibe 2004


The bearing is pressed into the knuckle. You will need to bring the knuckle to a machine shop or repair shop to have it pressed out and the new one pressed in. To remove the knuckle first remove the axle nut from the axle. Unbolt the caliper and bracket. Remove the rotor. Remove the outer tie rod from the knuckle. Seperate the lower ball joint from the knuckle. Unplug the abs harness if equipped. Remove the bolts that secure the strut to the knuckle. Finally remove the knuckle from the vehicle. When you reinstall everything it is vitally important the torque the axle nut to the proper spec. Failure to do so will result in the premature failure of the new wheel bearing. I would also advise getting a quality wheel bearing from a reputable manufacture. SKF is a well known and trusted brand.

Jan 14, 2012 | Cars & Trucks

1 Answer

Loud tumbling noise while it is going. How do i open the top of dryer to see the drum?


Sounds like a drum suppot wheel may be locking up and has a flat spot on it causing the "tumping noise. You usually have to remove the front panel to remove top, which you don't have to do to check out support wheels, it's a little more involved, but fairly simple. Look for two screws at the bottom of front panel, either get dwon on the floor & look up or feel for them, cant see them standing, kinda hidden for appearance. Remove screws and pull out on the bottom of panel, the top of panel is held by 2 snap-in clips which should pop out as you swing out the bottom of panel, exposing drum retainer brackets which hold the front drum cover. Remove these to remove drum or access screws holding top down to sides. There is no need to remove top to check support wheels, just remove belt from tensioner & motor pulley and drum should come right out the front exposing the 2 support wheels at lower back of dryer, their held on shaft by a snap ring. If your this far, check Teflon bearings on front drum end. they are 2 flat strips of Teflon rivoted in place. The drum simply slides on them. Replace felt seals on both ends of drum covers if worn. Wheels are $16 to $20 each. Hope this is helpful & cures your problem.

Feb 13, 2011 | Dryers

1 Answer

Speedometer not working, heard a noise from front wheel hub a few miles before, attached cable at hub, detached at top and when the wheel is spun the cable does not spin. Please advise.


It is probably the small differential on your front wheel. Most of these little devils are plastic and can be worn in zero time if not properly greased. You got to remove the wheel, and check it out.

Aug 08, 2010 | 2005 kawasaki KLR 250

1 Answer

Clicking sound in right front wheel, feel like it is the wheel bearing. Need advise on how to repair


If this is a front wheel drive car then the sound is the Constant Velosity (CV) joint, usually happens when the CV joint boot tears and let in road debris. You can remove the shaft and knock the joint off the shaft clean and replace boot and refill with grease, you will need a CV Boot Kit for your car, or you can replace the shaft. Hope this helps, let me know.

Aug 08, 2010 | Ford F-150 Cars & Trucks

1 Answer

Removal of rear right hand wheel


The snap ring can be removed with a screwdriver and needle nose pliers. Be sure you dont loose the key stock that alignes the axle and wheel.

May 12, 2010 | Garden

1 Answer

Removing front wheel (flat tire)


The lug nuts are the only thing holding the wheel on, aside from a little rust in some cases. Stand in front of the tire facing away from it, try giving it a swift kick on the edge. Of course, you must exercise caution when doing this. Be sure the vehicle is properly supported and won't fall the jack stand.

Nov 30, 2009 | 1994 Ford Escort

Not finding what you are looking for?
2004 Skyteam ST 200 OF Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Skyteam Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Nicola Conroy

Level 3 Expert

1373 Answers

Are you a Skyteam Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...