Question about 2008 KTM 250 EXC

1 Answer

Having trouble removing the seat from my KTM250

My battery has gone flat on the bike and I am trying to remove the seat so that I can recharge my battery? What am I doing wrong?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 653 Answers

Still having trouble to remove your seat? LH side about midway you should find a key hole where you can insert you igniton key and turn it clock-wise to open the seat hatch. Good enough?

Posted on May 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you remove the seat?


It really depends on what make and model bike you have.

May 03, 2015 | Motorcycles

1 Answer

How do you remove the starter on a 03 Harley Davidson Dyna Low Rider?


Instructions
  1. Removal
    • 1 Remove the seat retainer screw from the seat mounting bracket using a ratchet and Allen driver. Lift the rear of the seat up and slide the seat toward the rear of the bike to disengage the seat from the frame and remove it from the bike.
    • 2 Don a face shield and rubber gloves.
    • 3 Remove the battery cover retaining screw from the bottom of the battery cover using a ratchet and Allen driver. Tilt the top of the battery cover out and lift the cover to disengage it from the battery tray.
    • 4 Remove the negative battery cable from the battery using a 10 mm wrench.
    • 5 Remove the positive battery cable from the battery using a 10 mm wrench.
    • 6 Unhook and remove the battery strap. Remove the battery from the tray. Remove face shield and rubber gloves.
    • 7 Remove the two top battery tray screws from the frame above the battery tray and the bottom battery tray screw from the inside of the battery tray using a ratchet and Allen driver.
    • 8 Remove the battery tray from the bike while guiding the battery cables through the holes in the battery tray.
    • 9 Remove the starter end-cover nut, using a ratchet and socket, and pull the end-cover off the starter.
    • 10 Pull back the protective rubber boot off the positive cable terminal. Using a wrench, remove the positive cable nut and then lift the ring terminal off the starter terminal stud. Unplug the solenoid electrical connector from the solenoid.
    • 11 Remove the two starter retaining bolts from the starter using a ratchet and Allen driver. Pull the starter off the bike. Remove and discard the starter housing O-ring.
    Installation
    • 12 Inspect the two split-ring bushings in the inner primary case where the starter mounts for slack or looseness. Remove the split-ring bushings and spread them to provide a slight interference fit in the primary housing. Push the split-ring bearings back into position.
    • 13 Install a new starter housing O-ring on the starter assembly. Install the starter assembly on the bike.
    • 14 Apply one drop of Loctite Threadlocker 243 to the treads of the starter retaining bolts. Install the starter retaining bolts and washers and tighten them to 24 to 27 foot-pounds using a foot-pound torque wrench and Allen driver.
    • 15 Install the positive cable ring terminal and nut on the starter terminal stud. Tighten the nut to 65 to 85 inch-pounds using an inch-pound torque wrench and socket. Push the protective boot securely over the positive cable terminal. Plug the solenoid electrical connector into the solenoid.
    • 16 Position the starter end-cover on the starter and install the nut, using a ratchet and socket.
    • 17 Place the battery tray in position while guiding the battery cables through the holes in the tray.
    • 18 Install the upper and lower battery tray screws and washers. Tighten the screws to 96 to 120 inch-pounds, using an inch-pound torque wrench and Allen driver.
    • 19 Guide the battery cables into the recesses at the upper corners of the battery tray.
    • 20 Don face shield and rubber gloves.
    • 21 Place the battery in the battery tray with the terminals facing out. Snap the battery strap in position.
    • 22 Install the positive battery cable and cable bolt. Tighten the bolt to 60 to 70 inch-pounds using an inch-pound torque wrench and socket.
    • 23 Install the negative battery cable and cable bolt. Tighten the bolt to 60 to 70 inch-pounds, using an inch-pound torque wrench and socket.
    • 24 Remove the face shield and rubber gloves.
    • 25 Apply a light coat of corrosion retardant grease or petroleum jelly to the terminals.
    • 26 Install the battery cover and screw. Tighten the screw securely using a ratchet and Allen driver.
    • 27 Place the seat on the bike. Lift the rear of the seat and slide it forward to engage the seat tab in the frame slot. Lower the rear of the seat and install the seat retainer screw through the seat mounting bracket. Tighten the seat retainer screw securely using a ratchet and Allen driver. Lift up on the seat to make certain that it is mounted securely on the bike.

Jul 08, 2012 | 2003 Harley Davidson FXDL Dyna Low Rider

1 Answer

How do you remove the battery from a Suzuki van van 125 motorbike? mine is flat and i need to remove it to charge it up again.


On my TW125 Yamaha very similar to the Van Van. the battery is under the seat. There are 2 6mm bolts that fix the seat to the sub frame. Try using a torch or light and look under the seat from the chain side. The only other method of seat fixing i am aware of on Suzuki bikes involves removing the plastic panels under the seat and this reveals the seat fixings. Please remember when you remove the battery undo the negative lead first. Please do not use a charger with an output of more than 1 amp. When you refit the battery please connect the positive lead first.

If the recharged battery works OK please check the charging circuit is OK. Connect a volt meter across the battery terminals and see if the volts rise to about 14.5 as the revs are increased. Hope this helps

Feb 03, 2011 | 2006 Suzuki RV 125 VanVan

1 Answer

I just bought a 1989 kawasaki but im having trouble starting it, but i think the battery is dead. i want to know how to change the battery


Hi,
It is located below your seat. Just try open your seat or from sides of bike. Check the AH of battery and replace it with similar one.

Jan 28, 2011 | 2008 kawasaki Ninja 250R

1 Answer

I'm having trouble removing the battery from my 2004 FWDWG Dyna Wide Glide. Any suggestions?


Well. let's see if Harley has changed anything. I can tell you how the earllier Wide Glide batteries came out and we can see if Harley has changed thing drastically. I doubt it.

First, remove the seat. The bolt at the rear of the seat screws into the rear fender. Remove the bolt, raise the rear of the seat and pull it to the rear. The seat should come off. On some bikes, you may have to remove the small sissy bar by removing the two small bolts on either side of the uprights on it.

Now, you'll see the battery box on the right side of the bike. Look just rearward of it and you should see two bolt heads between the battery box and the rear wheel. The are battery tray lock bolts, loosen them but don't take them out.

Now, look just inboard of the battery into the frame. You'll see the head of a "jackbolt". Turn the screw counterclockwise and the battery tray will lower and allow you to get the top cover and the surround off. From there you can get to the cable connections at the battery post.

I hope this works for you.

Good Luck and Ride Safe.
Steve

Dec 19, 2010 | 2004 Harley Davidson FXDWG - FXDWGI Dyna...

1 Answer

How do i remover the seat the bike has power but when you got to start it all the bikes power dies


Sounds like a flat battery.
Depending on the model, to remove the seat you may have to
remove side panels to expose bolts holding the seat in place.
Then lift it up, it usually has a slot fitting at the front.
Now the battery is usually easy to access.

You'll probably need a small socket wrench, around 8mm to 11mm
These sets are quite cheap.
Hope this helps,
Tom.

Oct 31, 2010 | Suzuki GSX 1300 R Hayabusa Motorcycles

1 Answer

How to recharge the battery on a 2005 636 ninja?


Assuming you have just left the bike for a while and not removed a battery lead so it is flat (not the alternator is shot), then bumb start the bike and take her for a 5 mile journey, without stopping too much. Do some low speed, 3rd gear pulls to 60mph. This will charge the battery.

If it is the original battery, and it doesn't recharge after this, check the condition of the alternator and get a new battery.

Hope this helps matey :)

Jul 03, 2010 | 2005 kawasaki ZX-6R

1 Answer

Battery removal


Hi,

To my knowledge and on most versions/models, the battery would often be located under the seat. In your particular model, I believe the air cleaner box has likewise to be removed to gain access.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information. Good luck and kind regards. Thank you for using FixYa.

Nov 13, 2008 | 2008 kawasaki Z750

1 Answer

Flat battery-applied incorrect rdio code numbers found correct code no at home but radio will not accept it. tied disconnecting battery again -no success tried leaving radio turned on for 1 hour as per...


im sorry im having a little trouble understanding the ?tion, are you trying to remove the radio the correct way or install it and having trouble getting the code off the screen...

Aug 11, 2008 | Car Audio & Video

Not finding what you are looking for?
2008 KTM 250 EXC Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Brian Anderson

Level 3 Expert

356 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...