Question about 2008 Triumph Sprint ST Abs

Open Question

Change a clutch

Need to change a clutch

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have problem with my Nissan terrano 2 mechanical gearbox. It's hard to put to 1st gear. From 1'st to 2nd, 3rd, 4th, 5th, are also hard. Is it necessary to change clutch?


not a clutch problem unless you have just done a clutch kit change
more likely a hydraulic clutch problem ( air in the system) or master cylinder needing replacement .
if it is a cable operated clutch , replace the clutch

Dec 14, 2016 | Nissan Cars & Trucks

3 Answers

My clutch intermittently shudders/vibrates when depressed. Is that a sign it is failing?


The short answer is YES. Most likely a warped clutch, will need a new pressure plate and clutch disk and in the worst case fly wheel replaced or machined. The good news is that it could last for awhile before complete failure or until you get annoyed and wish to replace it.

Apr 13, 2015 | 2005 Hyundai Tucson

1 Answer

Loud snapping noise heard when changing gears


From the way you've described it your gear stick linkages maybe on there way out. When changing gear does the car resist getting into gear?

If it's more of a crunching sound then I would try double de clutching, to do this you need to:
change gear as usual but instead of holding down the clutch throughout the gear change hold it down to take the vehicle into neutral then release the clutch then push the clutch down again and change into desired gear.
To change down it's basically the same principal but you push down the clutch to put the vehicle into neutral then push the throttle down just to pitch revs then release the throttle and push the clutch down to change into your desired gear, if it won't go in to gear easily then rather the throttle until it does.

You can go onto youtube and search for double de clutching and I'm sure some results will come up

hope this helps!

Apr 30, 2014 | 2004 Nissan Altima

2 Answers

Freelander clutch


check out the operation of the clutch system .IT is difficult to rationalise a hydraulic clutch because if it is slipping that means that the pressure plate is being held off and not fully engaging but it also means that when pressing on the clutch the there would be no problem changing gears . But if you have a cable clutch operation then it is possible that the cable is jamming inside the outer cover and holding the pressure plate off ( slipping) and gear problems. If it is cable then replace the cable first. If hydraulic then it may mean box out for a new clutch kit.

Jan 12, 2014 | Cars & Trucks

1 Answer

Hyundai excel 1996 have to double clutch to change gears


Where is clutch engaging? close to firewall or up high on pedal. If up high, your clutch needs replacing, Low, your clutch is ok, maybe throwout bearing is bad or air in system or not adjusted correctly

Apr 05, 2013 | Cars & Trucks

2 Answers

Approximately how many miles before you need to change the clutch on an o7 cbr 1000?


You do not count how much mileage it has before changing clutch, it all depends how you use the gears and clutch...I had a cg125 and I had 40+ k miles and the clutch was absolutely fine...Just make sure you service it and change the oil when needed which will give it longer lifetime...Hope this helps.

Nov 24, 2009 | 2007 Honda CBR 1000 RR Fireblade

1 Answer

Audi a4 tdi stiff gearchange worse when hot 1197 model


tandard practice to change the oil on a clutch replacement. Was the replacemmiles it's covered, but it's not sounds like the gearbox oil need changing. You don't say how many miles it has done. Gear box oil is not usually changed in a clutch replacement. Did an Audi garage carry out the rlacement? It could be the cable needs adjusting to allow the clutch to have free movement

Jul 23, 2009 | 1997 Audi A4

1 Answer

Clutch won't engage--cannot shift


hydraulic clutch needs servicing or needs bleeding like a brake system wont work with air in the lines neither will hydraulic clutch's. you shouldnt have to change the clutch just service the slave cylinder ,that should give you back some pedal to use..you might want a mechanic to bleed it or have it replaced.

Jan 05, 2009 | 1994 Mercury Tracer

2 Answers

How to adjust clutch vw golf 1.4 1997 or changing


good point but even if it is the cable one its automatic,hydraulic is non adjustable.if it is the cable operated one the clutch is mounted to the back of the flywheel,nothing difficult but you will need the round alignment tool,if its hydraulic it could have a dualmass flywheel which it is advisable to change thats a straight forward job to do is it a 1j chassis build 7th and 8th digit of the vin number

Dec 30, 2008 | 1997 Volkswagen Golf

Not finding what you are looking for?
2008 Triumph Sprint ST Abs Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...