Question about 2002 Yamaha TT-R 125 L

1 Answer

How do i put my chain back together after i took links off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Yamaha Master
  • 1,508 Answers

You wiil need to take the removed links to a bike shop and buy a joiner link which will clip together, They will match the link to your chain.

Posted on May 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I just put a timimg chain an water pump in a 2001 chrysler sebring 2.7 liter engine an it will back firer at start up an not run .no matter how many times i check timing marks everytime it seems to no


I just recently experienced the same problem. The timing is 180 degrees out. Unfortunately the only way to correct it is to take the engine apart again. Set the right hand camshaft to TDC by using the marks on the timing gear for that bank. The left will follow to the degree it can although you will have to manually hold the cam in position when you put the timing gear back on. Now you can remove the timing chain. The crank TDC indicator may not be right on but it will be close. Rotate the crank CW one revolution to the point the TDC marks are lined up. Now install the timing chain according to the instructions. The timing gears on the camshafts will only go on one way as the bolt holes are slightly off the extreme diameter of the gear. If you put the chain back on making sure that all the marks are proper, she'll fire on the second cylinder up. Not a fun job I know, but when everything works right, you do get a sense of satisfaction.

Jul 13, 2012 | 2001 Chrysler Sebring

1 Answer

I took the bladeoff to oil and now can't remember how to get it back together.


i needed to replace my blade - my husband replaced it but it would not cut so we took it apart and cant figure out how to put it back together. nothing helpful on line.
did anyone have a link how to put all the pieces back together to create the blade? thanks

Jan 16, 2011 | Oster 76076-010 Hair Trimmer

1 Answer

Bar thru the chain, pulled the side cover off with difficulty and now cannot get the side cover back on, appears the roundish bearing on the cover won't go over the round bearing that covers the chain...


I just had the problem of not being able to put the cover back on because the brake wwas engaged when I took it apart. What I did was use a #4 allen wrench and take the brake lever off being careful of the spring on the brake handle. There is a screw on both sides. I then put the cover loosely in a vise, and using the brake handle reset the brake to the correct position. It went back together easily. Probably took me ten minutes.

Oct 30, 2010 | Husqvarna , No.455 Rancher, 20" Gas -...

1 Answer

Need to know how to tighten the chain, keeps falling off


I am not familiar with the Kett Car but I'll assume you've tried to see if there was an adjustment of some sort and you couldn't find one....So have you tried removing a link of the chain to shorten the chain? Chains can be shortened by taking one link out. Just realize that if you remove a link the chain may then be too short. So I'm not sure how much slack you actually have?
But to remove a link:
1) Find the master link where there will be little clip on the outside of one side of the chain and remove that clip and save it. It should slide off with a little pressure.
2) The Master link with the clip removed (mentioned above) can be taken out and the chain will no longer be in a loop. Save the master link because you'll need to put it back together after.
3) To remove a link, using a file or a grinder...grind off the last link on eather side of the chain. Use your Master link to see how far or how many links you'll need to remove. Remember, the master link will have to go back in to make the chain a loop again so you want to remove the link in the right place and not remove any more links than you need to.
4) Once you find where you want to remove the link, If you can visualize the letter "H" as a chain link, where the cross bar is there will be a silver piece on each side of the outside of the chain. This is what you want to grind off just on one side of the chain.
5) You'll see how the chaing is put together and using a punch, you can tap out the center cross piece. What you should be left with is (if I could put these sideways it would be easier to show) an 8 on one end of the chain and an 8 on the other side.
6) The master link will go back into the ends of these and rejoin the chain. Master links and chainds can be bought at most hardware stores so if you cut off too much you can replace the chain or master link.
7) If you do need to get a new chain, take the old one with you so you can get the right size.

Sep 26, 2010 | Kettler Classic Flyer By Kettcar Pedal...

2 Answers

Chain came off r70 riding mower how do i put it back on


ok there is three sprockets one on the transmission a guide in the middle and onle on your back axle. take a wrench and loosen up the middle sprocket. slide it all the way back untill the chain is snug or tight. tighten up your bolt and it should notice it drives faster and thats how you keep it from falling off. hope it works for you

May 15, 2010 | Garden

1 Answer

Back wheel tightens on fork when secure the nuts


yes u forget to put the washer..before the nut...check all this other wise u got the same problem means check your chain adjustment propely. because some time your refit the wheel means that got problem in chain adjustment. better u go for bike mechanic shop

Apr 30, 2010 | 2007 Ducati 1098

2 Answers

How do i put the brake assembly back to gether


If your saw is indeed a Husky there is likely an illustration of the chain brake on the IPL here:
HusqvarnaUSA.com
http://www.husqvarna.com/us/homeowner/support/download-manuals/
Enter the 3 digit model number (no XPs, Es, just the numbers)
Serial number decode – for use with IPL
06 1500198
06 = year produced – 2006 (single digit before 2000)
15 = week produced - March
00198 = 198th unit Husky produced that week

Oct 26, 2009 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

2 Answers

I have a pacific usa mountain bike and the chain broke an i bought a chain and I cant figer out how to put it back together


well usually all chains have a link that comes off. if you get that to come apart, then you put the chain on the teeth were the teeth come through between the links. then you link back together the two chain links. it might be a little hard though

Mar 08, 2009 | Mountain Bicycle Chain Press Fit 42 In ...

1 Answer

Timing chain gear marks up or together and spark plug diagram wir


put the dots together, pull out num 1 plug bring num 1 piston up too top dead center on compression stroke,

Mar 05, 2009 | 1991 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2002 Yamaha TT-R 125 L Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...