Question about 2003 Gas Gas Pampera 280

1 Answer

Back break not working wen u push it down

I tried bleeding back break but there seems to b air stil in systems

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 653 Answers

Keep on bleeding until all air bubbles goes out but never-never let your brake fluid reservoir empty, as you bleed the brake, fill the reservoir immediatel to full level. Do you know how to bleed properly? Make sure the engine and key is is off position. Pump the foot brake 6 or 7 times until it becomes hard, keep pedal down, open brake nipple relase fluid as soon it stop spurting, close tight and repeat process until all air bubbles are out from system, fill brake fluid reservoir. As the bike is on centre stand,hand turn the back wheel and press foot brake it should stop it from turning which means it is now working properly. Good enough advise?

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1999 Yukon with bad abs our the ecu I can not seem to get the air out of lines


ya there not easy when I do lines I have to cycle the abs motor a lot to get air out you will need a scan tool to do it at home I use my old snap on one

Mar 17, 2015 | 1999 GMC Yukon

2 Answers

Spongy breaks after bleeding on a 1997 ford expedition


the is still air in the system, rebleed the brakes starting with the- right rear-left rear- right front- left front. some vehicles with ABS need to be running so the abs system gets bleed properly.

Feb 24, 2012 | 1997 Ford Expedition

2 Answers

When i step on the brake pedal it goes all the way down, what's wrong?


You have air in your brake lines. Try inspecting the system for brake fluid leaks. Replace any worn out brake pads, scored discs, leaking brake piston seals, etc.Now place a clear tube on the bleeder screws, one at a time , and bleed the air out of the system with the help of a friend to push the brake pedal. Start at the rear wheel cylinders and finish with the front calipers. Once the air is out of the lines the pedal should firm back up.

Oct 27, 2011 | 1995 Toyota Corolla

2 Answers

My volvo s70 break pedal goes all the way to the floor ad new master cilinder new bled nipals stil after 2week its gone back down again what do i do next


It sounds like you have a small brake fluid leak, allowing air to enter the system. Small leaks can be hard to find. You will have to remove the wheels in order to inspect the calipers. Also make sure the bleeder valves are tightened securely after bleeding the brakes. Did you bleed the master cylinder when you first installed it? If you can't find a leak, bleed the entire system again, including he master cylinder.

Feb 15, 2011 | Volvo S70 Cars & Trucks

2 Answers

Problem with bleeding my breaks


You need a special tool that plugs into the ABS hydraulic control unit and holds the POP-IT valves open to bleed the air out, unless you have that tool you will keep spinning your wheels, most brake shops have a tool to do this or the dealer of course will have it.

Dec 23, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

Back brake not working?


you need to bleed all 4 brakes. have someone push the brake pedal while you open the bleeder valves on each caliper or brake line. close the valve or tighten the line efore the person pressing the pedal reaches the floor. monitor the fluid level because you will loose fluid while bleeding the brakes.

Nov 16, 2009 | 1999 Chevrolet Cavalier

1 Answer

Having trouble bleeding the clutch cylinder can you help ?


Start at the master cylinder on the handlebars and crack the banjo bolt loose first. Bleed the line there, just like you would at the slave cylinder. Break the bolt loose about 1/4 turn while holding the lever in. Tighten the bolt back up and pump the lever again, hold it and break the bolt loose 1/4 turn. Keep doing this till you do not get air out of the system, just fluid, then move down the clutch line to the next fitting and bleed it there the same way. Work your way back down to the slave cylinder finally bleeding it at the bleeder valve. You should now have hydraulic pressure all the way through the system when you pull the lever. If you want to test it. wrap a rag around the rubber clutch line a few times and pinch it off with a pair of needle nose pliers. Now try to pull the lever. If it gets hard instantly, you don't have air in the lines. If it is hard then, and the clutch STILL doesn't work, you have other problems than air in the lines.

Sep 19, 2009 | 1994 Suzuki VS 1400 Intruder

1 Answer

Breaks will not work!


i think you pumped the air out in the wrong way. the proper way is called bleeding. you bleed the air and break fluid at the same time. to do this you need to be accompanied by a helper. but i think we need to chat on ym so that i can tell you the step by step instruction. if you have time just let me know.

Mar 19, 2009 | 2002 Audi A4

Not finding what you are looking for?
2003 Gas Gas Pampera 280 Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gas Gas Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Kim Halliwell

Level 1 Expert

32 Answers

Livewyre Studio
Livewyre Studio

Level 1 Expert

26 Answers

Are you a Gas Gas Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...