Question about 1988 Yamaha YX 600 Radian

1 Answer

CAN NOT GET KEY TO LOCK POSITION----PUSHES DOWN BUT WILL NOT GO TO LOCK OR PARK

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Yamaha Master
  • 1,508 Answers

It may only lock if the handbars are on full lock, usually to the left, try wiggling the bars at full left lock as you try the key

Posted on Apr 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 chrysler 300M won't shift out of park. Pulled so ******* the shifter it broke.


possible internal locking pawl stuck fault or adjustment required

ADJUSTMENTS
sourced from another forum

The park interlock cable is part of the brake/shift lever interlock system. Correct cable adjustment is important to proper interlock operation. The gear shift and park lock cables must both be correctly adjusted in order to shift out of PARK.

ADJUSTMENT PROCEDURE

1. Remove floor console as necessary for access to the park lock cable.

2. Shift the transmission into the PARK position.

3. Turn ignition switch to LOCK position. Be sure ignition key cylinder is in the LOCK position. Cable will not adjust correctly in any other position.
NOTE: If the key will not turn to the LOCK position, pull up on the cable lock button and manually move the cable in and out until the key can be turned to the LOCK position.

4. Pull cable lock button up to release cable, if necessary.

5. Remove and discard the cable adjuster lock pin, if a new cable is being installed.

6. Ensure that the cable is free to self-adjust by pushing cable rearward and releasing.

7. Push lock button down until it snaps in place. The lock should be 1-2mm below the surface of the cylindrical portion of the cable



d5fad53b-454e-40de-8326-5998ee796fd6.jpg2010-09-06_193640_8-yevmkukx3b2zymzwvvrzuy4i-4-2.gif

Jan 16, 2017 | 1999 Chrysler 300M

1 Answer

Holden cruze 2009 key stuck in the ignition won't go to off position , can't get it out of park .What is the problem ?


Is it shifter on the floor ?
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator's purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control actuator , and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.

GM had problems with these ! Has a TSB - technical service bulletin !
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will remove voltage from the shift lock solenoid:
- The ignition is in the ON position.
- The engine control module (ECM) sends an input via GMLAN serial data to the BCM indicating the transmission is in the PARK position.
- The BCM determines the brake pedal is applied according the brake pedal position.
Since the shift lock control solenoid is permanently grounded, the BCM supplies voltage to the automatic transmission shift lock control solenoid, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the control voltage output of the shift lock control solenoid OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
During remote start operation, the BCM will energize the shift lock control circuit, locking the shift lever in the PARK position.
Replaced shifter on a cobalt , broken plastic part inside , wouldn't press on micro switch to disengage ! Found replacement shifter at auto slavage yard .$20.00 US

Sep 03, 2016 | Holden Cars & Trucks

1 Answer

1999 Volvo S40 cannot remove key


What make vehicle ? Most all vehicles have a safety system .Don't try an force anything you'll break it !
Electronic Park Lock (EPL)/Ignition Lock Cylinder Control Actuator: If the vehicle is equipped with automatic transmission and a floor mounted console gear shift, it has an ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in any position other than PARK and the vehicle may still be moving. The column ignition lock system consists of an ignition lock cylinder control actuator, and a park position switch that is located in the automatic transmission shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. They also have this on column mounted shifters !

Aug 19, 2015 | Cars & Trucks

1 Answer

How to remove my Keys from 2003 envoy they are stuck


Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column as an added safety feature. The ignition lock cylinder control actuators purpose is to prevent the steering wheel from being locked when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control acutator, and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control acutator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. GM has had some problems with this , If you have the console shifter there is a micro switch that when put into park a linkage pushes on this micro switch closing the circuit to ignition lock cylinder control actuator allowing you to remove your key ! These linkages fall out causing this problem ,an have electrical wiring problems as well ! I fixed a 2006 Chevy cobalt that had this same problem by getting a used shifter assembly at the auto salvage year ! cost $20.00 . There mite be a access hole under the bottom of the steering column with a release button up inside !

Apr 17, 2015 | 2003 GMC Envoy

1 Answer

Key trapped in ignition


Could be the ignition lock or switch, but it could be the shifter too.
If the shifter is not completely in park, the key will not go to the lock position.

Feb 17, 2014 | 1998 Chrysler Cirrus

1 Answer

How do I change the ignition switch in my 93 plymouth van?


FIRST OF ALL, TURN OFF RADIO,DISCONNECT NEGATIVE BATTERY CABLE. IF EQUIPPED WITH TILT STEERING COLUMN,REMOVE TILT LEVER.CAREFULLY REMOVE THE UPPER AND LOWER STEERING COLUMN COVERS. REMOVE THE 3 TAMPER PROOF TORX IGNITION SWITCH MOUNTING SCREWS USING SNAP ON TOOL TTXR15A2 OR EQUIVALENT. GENTLY PULL THE SWITCH AWAY FROM THE COLUMN AND REMOVE THE 2 ELECTRICAL CONNECTORS FROM THE IGNITION SWITCH. WITH THE KEY IN THE LOCK POSITION, DEPRESS THE KEY CYLINDER RETAINING PIN FLUSH WITH THE KEY CYLINDER SURFACE. ROTATE THE KEY CLOCKWISE TO THE OFF POSITION THE KEY CYLINDER SHOULD NOW BE UNSEATED. ROTATE THE KEY CYLINDER COUNTER CLOCKWISE BACK TO THE LOCK POSITION, AND REMOVE THE LOCK CYLINDER. ( TO INSTALL ) CONNECT THE ELECTRICAL CONNECTORS TO THE IGNITION SWITCH. BE SURE THE CONNECTORS ARE SECURELY LOCKED IN PLACE. MOUNT THE IGNITION SWITCH TO THE COLUMN 3 SCREWS FOR VECHICLES WITH THE TILT STEERING COLUMN THE SHIFTER MUST BE IN THE PARK POSITION AND THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG MUST BE INDEXED BEFORE THE SWITCH IS INSTALLED. PLACE SHIFTER IN THE PARK POSITION. PLACE THE IGNITION SWITCH IN THE LOCK POSITION. THE SWITCH IS IN THE LOCK POSITION WHEN THE STEERING COLUMN LOCK FLAG IS PARALLEL TO THE IGNITION SWITCH TERMINALS. POSITION THE PARK LOCK DOWEL PIN OF THE IGNITION SWITCH SO IT ENGAGES THE STEERING COLUMN PARK LOCK SLIDER LINKAGE. APPLY A LIGHT COATING OF GREASE TO THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG. POSITION THE IGNITION SWITCH AGAINST THE LOCK HOUSING OPENING ON THE STEERING COLUMN. BE SURE THE SWITCH PARK LOCK DOWEL PIN ENTERS THE SLOT IN THE PARK LOCK SLIDER LINKAGE INSTALL THE RETAINING SCREW AND BRACKET. TORQUE THE SCREW TO 26 INCH LBS. INSTALL THE STEERING COLUMN COVERS AND THE TILT LEVER IF REMOVED. WITH THE KEY CYLINDER AND THE IGNITION IN THE LOCK POSITION INSTALL THE KEY CYLINDER INTO THE SWITCH UNTIL IT BOTTOMS. RECONNECT THE NEGATIVE BATTERY CABLE AND THE CHECK THE IGNITION SWITCH FOR PROPER OPERATION OF HALO LIGHT SHIFT LOCK IF EQUIPPED AND COLUMN LOCK.ALSO CHECK FOR PROPER OPERATION OF THE IGNITION SWITCH ACCESSORY, LOCK OFF, RUN AND START FUNCTIONS.

Sep 18, 2010 | 1993 Plymouth Voyager

2 Answers

Have a 1887 pontica grand am cant get the ingition swicth out what can i do


Take the shifter and push it up past park. That usually works, Or give the shifter a little wiggle. There is a locking system in there that can cause the key not to fully go to the off position.
If it does go completely to the off position, then the pins in the ignition switch could be stuck and a lite tapping with a ballpeen hammer around the switch can loosen them up.

Sep 02, 2010 | 1997 Pontiac Grand Am

1 Answer

2005 GMC Envoy key is stuck in accessory position in the ignition with dead battery and transmission stuck in park. Will replacing battery help or is it security system lock down? If it is the security...


Jump starting the battery may be all you need. If this vehicle was not in park when the battery went dead and when you got in to start it it was dead. You then probably put it into park trying to start it.
But the issue at this time is if it was in neutral when the battery went dead the you changing the selector to park may not actually have placed the transmission in park. With electronic gear selection it actually need power to the system to place the transmission in park.
Without it really being in park the key may move to the lock position.
A bit of quess work here but I hope for you I hit the mark.

May 20, 2010 | 2005 GMC Envoy

3 Answers

Igniton key is stuck in switch and won't turn off


Check the shift cable to the shifter to the transmission,and the shifter could be malfunctioning.

May 16, 2010 | 2004 GMC Envoy

1 Answer

Hello i have a 2004 cavalier and it will not go into gear can you help me?


This Is Park Lock Cable Failure here is the Replacment Procedure

Park Lock Cable Replacement

Removal Procedure

  1. Disconnect the negative battery cable.
  1. Remove the console.
  2. Remove the knee bolster.
  3. Loosen the lower steering column bracket bolts.
  4. Lower the steering column.
  5. Place the transmission shift lever in the PARK position. Important: Do not proceed to the next step with the key in any position other than the RUN position.
  6. Turn the ignition key to the RUN position.
  7. Insert a screwdriver blade into the slot provided in the ignition switch inhibitor.
  8. Depress the cable latch. Pull the control cable from the inhibitor.
  1. Push the cable connector lock button at the shifter base to the up position.
  2. Unsnap the cable from the park/lock lever pin.
  3. Depress the two cable latches. Remove the control cable latches from the automatic transmission control.
  4. Remove the control cable clips.
Installation Procedure

Important: When installing a new park/lock cable, keep the shipping cover gauge attached until you are instructed to detach it. The shipping cover gauge will aid in the proper positioning of the cable.


  1. Ensure that the cable lock button is in the up position. Place the shift lever in the PARK position.
  2. Snap the control cable connector into the automatic transmission control.
  3. Place the ignition key in the RUN position. Important: Do not insert the cable with the key in any position other than the RUN position.
  1. Snap the control cable into the inhibitor housing until the snap lock is seated.
  2. Remove the shipping cover gauge.
  3. Turn the key to the LOCK position.
  1. Snap the control cable end onto the shift park/lock lever pin.
  2. Push the cable connector hose forward in order to remove any slack.
  3. With no load applied to the connector nose, snap the cable connector lock button down. Important: Inspect for proper operation of the park/lock control cable before installing the steering column to the instrument panel.
  4. Raise and connect the steering column.
  5. Tighten the lower steering column bracket bolts.
  6. Install the knee bolster.

Apr 08, 2010 | 2004 Chevrolet Cavalier

Not finding what you are looking for?
1988 Yamaha YX 600 Radian Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...