Question about 2005 Honda CR 125 R

1 Answer

I need spears for my x-stream x dirt sport 125

I need parts to fixmy bike its a 55 reg and i need some bits i will bye a hole bike at rite price

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 64 Answers

If you need a hole bike you may as well ride it instead.

Posted on Apr 29, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Have drz125 cleaned carb an tank,starts on choke,idles for 2-3 seconds and dies,also need to know settings,thanks

The carb on a DRZ 125 or KLX 125 comes pre-set from the factory with a very lean tuning. At first it may run well but once you get some time on it with a little build up and some dirt the lean setting gets even worse. To correct this you need to thoroughly clean the carb , specifically the fuel screw. Remove the carb from the intake and airbox rubbers and take off the slide cap. Drain the carb from all fuel. The fuel screw is in a recessed tube located on the bottom of the carb on the front side towards the cylinder. It may ahve a brass plug covering the screw. This is done at the factory to prevent tampering for emissions purposes. The plug can be removed by taking a very small drill bit 1/8" or so and very carefully drilling a hole in it. Put a small sheet metal screw in the hole and pull with pliers and it should come out. Make a note of the position of the screw and slowly turn it clockwise in to see what the setting is. Do not apply heavy pressure when you feel it getting tight stop. It is a soft brass screw with a fine point an is easy to damage. Typically the factory settings range from 1 1/2 to 2 turns out. This is way too lean for the bike to idle and run well or even start without the choke. back the screw out and remove the spring and O ring. Using carb cleaner with the hose attached insert it into the hole you just removed the crew from and spray it out. You should have a good stream of spray into the center bore of the carb. Re-insert the O ring and then the spring and fuel screw. turn it in until you feel it making contact and then note the position and back it out 3 1/2 turns. Put the carb back on and it should be able to start and run without the choke. Some bikes will still need a bit more tuning. The older carbs had a slide needle that had 3 to 5 positions on the needle that could be adjusted with the movable clip. Since this does not have that option you could go to a Yamaha dealer and buy the needle from a TTR 125 and install it as it is the same carb. This will cost you around $15.00. Or you could go to a hardware store and buy some 3/0 stainless washers and remove the needle and put 2 or 3 under it to shim the needle up just like the clip on an adjustable needle. You may spend $1.00 with this option. The bike should run better than new.

Jan 24, 2011 | 2003 Suzuki DR-Z 125

1 Answer

When is duke 125cc will arive in nepal?how much will it cost

hi check here

Nov 26, 2010 | kawasaki Full Suspension Mountain Bike Men

1 Answer

Need to see how rear brake petal assembly looks like on 1980 rm 125 dirt bike thanks.

Here you are, just scroll down to the section you want and an exploded view of all parts, names and prices is there. Cheers.

Aug 14, 2010 | Suzuki RM 125 Motorcycles

2 Answers

Yamaha dirt bike igniter

Try looking at a workshop manual .if possible ,or contact you local dealer .

Mar 14, 2010 | 2005 Yamaha TT-R 125 E

2 Answers

How do youfind a serial number on a yamaha 125 dirt bike 2004

Should be stamped on the neck of your motorcycle or on the left hand side lower rail. Look on the neck, right side, under the dirt.

Where is the neck? It is the place where the front wheel assembly is fastened to the rest of the motorcycle.

Thanks for your interest in

Feb 20, 2010 | 2004 Yamaha YZ 125

1 Answer

How do i no wo model my bike is

Well if it looks like that picture, it's a dirt bike, not legal for street use. If it has head lights and blinkers, it is a dual sport. The engine size is stamped into the head. Like .125 liter or .250 liter. I think the dual sport is a KZ and the dirt bike is KX. That is Kawasaki.

Feb 20, 2010 | 2003 kawasaki KX 125

1 Answer

2005 Yamaha Ybr 125 sticking rev counter

Hi, Sheila_coope for more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Rev counter tachoemeter faulty
YBR125 55 plate with rev counter issues
Yamaha YBR 125 Service Manual
OEM parts for Yamaha
YAMAHA YBR125 Owner Manual

Jan 02, 2010 | 2005 Yamaha Ybr 125

2 Answers

Part of the engine that connects to bk wheel

u are better off replacing the whole engine bec in my exsperince u will spend around £200 pound fixing that u could pick up a another gilera runner engine for £150-£200 from ebay etc

Nov 16, 2009 | 2005 Gilera Runner VX 125

Not finding what you are looking for?
2005 Honda CR 125 R Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers


Level 3 Expert

76070 Answers


Level 3 Expert

4339 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides