Question about 2003 kawasaki KX 125

Open Question

How do I bleed the back brakes for a 1990 kx 80 and change the oil?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 dodge Dakota brakes seem to have air changed master cylinder still got air can't get it out bleed brakes


when bleeding brakes start at the master cyl lines. crak the nuts at the lines and pump the pedal until you have oil coming out . This primes the master cyl.. Next start at the longest line and bleed back to the shortest. Two man operation . Pump and hold down and then open the bleed screw . tighten the bleed screw and allow the pedal to come back up re-pump the pedal and hold down until all the air is out of that line. Repeat the process fpr all the lines ensuring that you monitor the oil level in the reservoir so that you do not have to start again.

Nov 13, 2014 | Cars & Trucks

1 Answer

Kawasaki kx 80 brakes


they should if you make them mate

May 31, 2013 | Motorcycles

2 Answers

Brakes wont work pedal goes to floor changed the master cyclinder bleed brakes and still have same problem 1990 ford aerostar van


What is the condition of both front calipers? both rear wheel cylinders? and the complete brake lines and hoses of your van? If they are all good with no traces of leakage, then did you bleed the Mastercylinder on the bench first before installing in the van? Did you gravity bleed the 4 wheels first? did you bleed from the farthest wheel first? Are you using a new Master and not a re-built??

Feb 25, 2011 | 1990 Ford Aerostar

1 Answer

Having problem bleeding brakes cant find the brake screw to bleed brakes to build pressure in brakes in a 1990 lexus ls400.


The bleeder screw is in the back next to the brake line into the caliper. Start the bleeding at the right rear, farthest from the reservoir. Then move towards the front left. Keep checking the fluid level and make sure you don't let go of the pedal with the screw loose. Get a 6 point box wrench on there , about 8mm, and a piece of hose to run the fluid into an empty can. Check it out, hope this helps.

Aug 29, 2010 | 1990 Lexus LS 400

1 Answer

1990 Honda accord brake problums


Your problem look like if there is still some air in the calipper cylinder.
I suggest you loosen the brake hose at the calliper and completely retract the piston.
Then thighen back the hose and perform a normal bleeding procedure of the front brake lines.
Spider guy

Mar 19, 2010 | 1990 Honda Accord

2 Answers

In my 05 kx 250 my brake pads were really worn out, so i changed them, and i put everything back together and now theres no pressure in my brakes to move the piston in the caliper. What do i do? add more...


Maybe air in the line..

Bleed the line..
Open the master,, then open the slave & let it drain.. At the same time keep adding fliud to the master as needed - dont let it drain to low - keep it topped off..

After you think the entire line has been drained,, close the slave & be sure master is at the right level & close..

That will release any air - if that was the issue..

Hope this helps !!
Please rate me good ;o)

Jul 12, 2009 | 2003 kawasaki KX 250

2 Answers

Cant bleed out brakes


It takes time, do you know the sequence to bleed the brakes? Most cars r different. And you have to keep pouring brake fluid, That is a two person job. Make sure all lines r connected to MC and not leaking. After a while if nothing comes out MC could be diffective.

Jun 06, 2009 | 1990 Toyota 4Runner

1 Answer

How do you bleed the brakes on a rmz 250 dirtbike the front brake


The way I bleed bleed front and back breaks on any bike is with a big vet suringe(full of fluid) with a thin tube from it to the caliper nipple and push til the bubbles stop coming,works for me give it a go.

Jan 23, 2009 | 2005 kawasaki KX 250 F

1 Answer

Brake bleeding


Start with the farthest from the master cylinder.
passenger side then driver.

Dec 31, 2008 | 1992 Audi 80

Not finding what you are looking for?
2003 kawasaki KX 125 Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...