Question about 2003 Yamaha DT 125 R

1 Answer

Do i turn my power valve clockwise or anticlockwise to open it on a dtr 125 2003 model

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 136 Answers

If you are turning to open up the valve for more power then you are making a mistake. power valves open the upper exhaust ports to allow the exhaust gas to exit faster being pulled by the exhaust pulses from the expansion chamber. by opening it and setting it in the fully open position would rob the engine of all its low down power making the bike useless below 5000 rpm which is where your power valve would start to open, it would also waste fuel as it would be sucked straight into the ex possible causing lean running conditions .

Posted on Apr 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to turn up the psi


off the memory - on this particular model you have knob just before the valve and indicator, lift it up and turn clockwise to increase pressure and anticlockwise to decrease it.

Apr 04, 2014 | Airbrush-Depot Master Airbrush Model G23...

1 Answer

Turntable turns anticlockwise


If the deck connects to a hif-fi system that powers the motor then the plug has been inserted in incorrectly.
If it has it's own power supply then either the belt is fitted wrong. Somebody trying to repair it has fitted the motor connection wrong or in the case of a direct drive model a fault has happened causing the motor to go into reverse.

Mar 23, 2014 | Denon Audio Players & Recorders

1 Answer

Clockwise or anticlockwise to undo blade bolt


On table saws to undo bolt is anticlockwise . Just lock blade against medal, with screw driver threw holes to hold blade tight and turn anticlockwise to losses. Make sure you unplug saw for safety of course . Thanks, Mike

Aug 10, 2011 | Saws

2 Answers

My power valve on my dtr 125 is not turning properly and my bike is realy slow got new servo motor and still the same


A have a yamaha dtr 125 it runs but its got no power and the valve moves but isn't kicking what could it be thanks

Apr 29, 2011 | Yamaha DT 125 R Motorcycles

1 Answer

Bathroom has a chrome radiator with two knobs at the bottom (one on each leg). I turned it off in the summer but now cant turn it on again. I have tried anticlockwise and clockwise and nothing happens. ...


Almost all valves turn to right or clockwies to close and left or counterclockwise to open. You might try spraying some WD-40 on bottom side of knobs.Let it set for a few mins. Tap on top of knobs lightly with a non marring tool such as wooden hammer handle and try to open. If it still wont open you can wrap knob tightly with masking tape or duct tape to protect the finish and use channel lock pliers or pipe wrench to try to open.Don't force it as you could break valve stem. Spray again with WD-40 and repeat above procedure until valve moves freely. Hope this helps. Thanks P:S WD-40 also works well to remove any adhesive left when you remove tape.

Nov 09, 2010 | Home

1 Answer

How to open a 911 petrol cap


hi well this will depend on what type of cap it is...there are a few different types, you have the standard type, just push and turn anti clockwise, the key locked type, put key in, hold the outside of the cap turn the key anticlockwise, and then you have the basic one, just turn anticlockwise ...hope this helps

Sep 15, 2010 | 1987 Porsche 911

1 Answer

Changing the front turn indicator bulb


open the indicator and give a turn to the fused bulb anticlockwise it will come out . replace it ang give it clockwise turn.. and fix the indicator again.

Aug 01, 2010 | 2002 Pontiac Sunfire

3 Answers

Ford focus estate - open bonnet


On my 05 model, you need to twist the ford badge on the bonnet anti-clockwise, pushing the left side of the badge down, which will reveal a keyhole. This is then opened with your ignition key. Once the bonnet pops, you just need to release the bonnet catch.
Hope this helps.

Apr 27, 2009 | 2005 Ford Focus

Not finding what you are looking for?
2003 Yamaha DT 125 R Logo

Related Topics:

577 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...