Question about 1992 kawasaki GT 750

Open Question

ENGINE RUNNING SPEEDO WORKS BUT TACHO NOT.WHEN YOU PRESS IN THE TACHO/VOLT RESET BUTTON IT MOVES.CAN YOU HELP

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 101 Answers

SOURCE: I have a wire plus WP124 which wont work on Vulcan

I would need to know the brand and model of the speedo to address that issue.
The tach is probably reading double because your ignition is firing every time the piston comes to TDC. One of the sparks is wasted because the engine is on the exhaust stroke at that point. Tach's sense that spark, but do not know it is a wasted spark, so it processes it as a compression stroke. You need to change the setting on the tach so that it thinks it is reading a 2 stroke single cylinder, then it will read correctly.

Posted on Sep 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why doesn't the cruise control work?


run the fault codes
cruise control needs the following to work together as one or more will stop it from working.
VSS sensor, (road speed /speedo)
engine rpms/tacho
brake switch sensor/
clutch switch sensor
cruise control switch

Jun 06, 2015 | 2005 SsangYong Rexton RX

2 Answers

How do i fix the tachometer?


you have an in cluster factory engine tachometer (RPM)?
the tacho is meter in the cluster and does not use speedo parts or its cable.
its just a meter that needs power, ground and spark tacho signals
if all 3 are good, the meter is bad. period.
the tacho signal goes to the ignition coil minus lug, and will good, as engine runs. so... wires bad, to tacho or tacho bad.
ever price a new one? or even used? $100 used?
you willing to pay that much for just a factory tacho?

there is NO speedo cable. this old 93 is electronic, (rare on most 93 cars made, toy is advanced)
here is the proof, amazing how books dont lie....
there is a speed sensor.
the tacho and speedo use the same power and ground
leaving just one wire,r-g red-green RPM sig. pin 5 of cluster
an is SPARK primary sig. so if only tacho is dead.
then the tacho is bad, or that pin 5 wire is dead.
got you to just 2 possibles.


25384019-pwhjtvbdga2ldpurmpdgxawg-1-0.jpg

Jan 26, 2015 | 1993 Toyota Corolla

1 Answer

2003 Satria, Tacho and Fuel gauge dont work . Fuel gauge comes up now & again low fuel light works. Tacho works now & again. But speedo and temp do work all the time.


It may be that the speedo and temp are mechanical, whereas the tach and fuel are electrical. Check fuse for inst. cluster for clean and tight fitment. Check electrical connection at back of inst. cluster.

Dec 09, 2014 | Cars & Trucks

1 Answer

I have a desiel pilote the rev counter does not work it is built on a boxer chasis


if you have a cable operated tacho or there is a cable to an electronic box that provides the pulse for the tacho the check that the cable is operational and is in the drive gear.

Aug 12, 2014 | Cars & Trucks

1 Answer

Tacho and speedo incorrect readings


compared to what?

tell method of test.
tell numbers. my engines idles hot at 800 (hand tacho)
but gauge reads in dash 200.
or im going 50mph ,my cell phone with free GPS shows 40.
why?
like that, use real numbers.

Jan 31, 2014 | 1992 Toyota Celica

1 Answer

Reset t/belt light


Have you got a rubber grommet in the instrument display (where the speedo and tacho is) about at the same level as the trip meter reset?

If yes then remove the grommet and there is a very small button if you straighten a paper clip and use it to just press the small button that should reset the T-belt light

Oct 09, 2012 | 2007 Toyota Quantum 2.5

1 Answer

I have a wire plus WP124 which wont work on Vulcan


I would need to know the brand and model of the speedo to address that issue.
The tach is probably reading double because your ignition is firing every time the piston comes to TDC. One of the sparks is wasted because the engine is on the exhaust stroke at that point. Tach's sense that spark, but do not know it is a wasted spark, so it processes it as a compression stroke. You need to change the setting on the tach so that it thinks it is reading a 2 stroke single cylinder, then it will read correctly.

Aug 29, 2009 | 2004 kawasaki VN 1600 Mean Streak

1 Answer

99 lancer,speedo tacho n gauge problem.


probably burnt or cracked circuit board on back of gauge cluster

Jun 21, 2009 | 2002 Mitsubishi Lancer

1 Answer

99 lancer speedo tacho odometer and temp guage


might check the ground wire under the drivers kick panel, some time the screw gets loose or may not have b een tighted back up, this will cause a tempory faiure on guages. hope i helped

Jun 13, 2009 | Car Audio & Video

Not finding what you are looking for?
1992 kawasaki GT 750 Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...