Question about 1995 Honda CBR 900 RR Fireblade

1 Answer

Spark plug how open do they have to be - 1995 Honda CBR 900 RR Fireblade

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 921 Answers

They should be changed about every 8000 to 10000 miles!. now if your referring to gap i would say approx .034. any feedback would be appreciated.

Posted on Apr 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steps to change a spark plug


Open hood remove spark plug wires get your spark plug socket, place over plug and remove.
tools needed, spark plug socket, extension and ratchet.

Apr 15, 2014 | 2005 Chevrolet Blazer

1 Answer

Ohv 179cc snowblower engine will not start


I'd check to make sure any fuel shut off valve (often "inline" or located directly under the tank) is open or on. Check or replace any inline fuel filter as well. If your snowblower has a priming bulb, you should hear gasoline spritzing after the second or third full press. More presses will probably cause gas to drip out of the carb to the ground. Next, check the spark plug. Clean or optionally replace it - set / check proper gap. With the plug out (and the spark plug wire away from the spark plug's threaded opening in the engine) pull the starting cord several times, and then check for the smell of gasoline in the cylinder. If no gas odor, you may have a bad float in the carb or other blockage. It will not run until you can get fuel into the cylinder. You can try pouring a few drops of gas into the cylinder of the engine via the spark plug opening or give it a "quick blast" of aerosol starting fluid or ether. Reinstall the spark plug and try again. If you added fuel, starting fluid or ether, the engine should have either attempted to run or sputtered briefly or is actually running. If it did neither, check for spark. Remove the spark plug wire from the spark plug and insert the tip of a screwdriver into the boot on the end of the spark plug wire and position the screwdriver's shaft to within 1/4" of the top of the spark plug. Be sure to only hold the screwdriver by the insulated handle (do not come in contact with the metal shaft of the screw driver) and pull the starting cord again. You should see a spark jump to the spark plug. If none, you may have a bad spark plug wire or magneto - and need to clean or replace it. before trying again. Good luck!

Feb 02, 2014 | Yard Machines 31A-62BD700 179cc OHV...

2 Answers

Where are the spark plugs on GMC 2002 Envoy


Follow the wires coming out of the distributor cap to the spark plugs.

Jan 23, 2011 | 2002 GMC Envoy

1 Answer

Will not start, it has fuel coming through and has a spark?


When I have a problem starting my saw what I do is;
  • Remove the spark plug
  • Pour about 5ml (one teaspoonful) of fuel into the opening
  • Wet the electrode end of the spark plug (The spark gap) with fuel
  • Replace the plug and try to start the saw.
The fuel you poured into the spark plug opening should ignite and cause the saw to start. The process may have to be repeated 2 to 3 times but should get it going. Don't be tempted to pour any more than the 5 ml of fuel in or you'll flood the saw.

Dec 14, 2010 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

2 Answers

My 5700 watt 11 HP McCullough generator wont start. I'm getting good gas to the plug but no spark.


The spark coil is bad if you have no spark

Small engine repair. Part is expensive.

Have you checked spark for sure?
1) Spray WD-40 directly into carburetor
If machine has spark, it will fire
2) Is exhaust port clogged with carbon and dirt?
3) Get new spark plug
Pull out old spark plug
Put spark wire on plug
Hold spark plug wire with fingers
Put spark plug threads against metal opening where spark plug came out.
Metal to metal
Pull cord or push starter
Look for spark between metal

No spark, then spark coil is bad.

Oct 25, 2010 | McCulloch 13HP 338 Cc Portable Generator #...

1 Answer

What should a multimeter read on a continuity test on the coil packs? i'm getting 1.9,1.7,1.7


The multimeter can read the resistance and if it is not open or shorted out, I'd say that your readings are in the normal range, comparing each resistance with each other + or - 10%.

I looked up the resistance readings on my online resource, but they did not list it specifically.
---
I looked up the following on autozone.com:

There are 3 dual-tower ignition coils that are part of the ignition control module (ICM). The ICM contains coil driver circuits that command the coils to operate. The Powertrain Control Module (PCM) controls each dual-tower ignition coil by transmitting timing pulses on the ignition coil control circuit to the ICM for the proper coil to enable a spark event.
  1. Inspect the spark plug wires for proper orientation.
  2. With the ignition OFF, remove the fuel pump relay.
  3. Crank the engine and test for a strong spark on each cylinder spark plug wire using a suitable spark plug tester. Ground the companion cylinder spark plug wire of each cylinder when it is tested.

    If a strong bright blue spark is present on all of the cylinders, remove and inspect all of the spark plugs for proper torque, proper gap, wear, damage, and fouling. Replace the spark plugs if necessary. If there is no spark on any of the cylinders, test the ignition voltage circuit of the Ignition Coil Module (ICM) for an open/high resistance or short to ground, or test the ground circuit of the ICM for an open/high resistance, or a faulty ICM. The wire circuit resistance should measure less than 3 ohms. If there is no spark on any of the cylinders, or spark is weak or intermittent, test the IC circuit for an open/high resistance, or a faulty ICM. The wire circuit resistance should measure less than 3 ohms. If spark is present on one or more of the cylinders, inspect and test the spark plug wires for arching, cuts, rubbing on other components, and proper resistance. If all tests are normal, then the system is operating correctly.
    ---

Oct 08, 2010 | 2000 Chevrolet Venture

1 Answer

Where are the spark plugs?


With the hood open, there is 4 spark plugs and their location is in the front side of the engine. Each plug has a spark plug wire attached to it. The spark plug wires run from the right side of the engine from the coils to the spark plugs.
Caution, make sure you clean around each plug before removing them so you don't get debris in the cylinders.

Jun 02, 2010 | 1997 Pontiac Sunfire

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

2003 dodge neon , unable to screw spark plug into one opening


go to the nearest parts store and ask for a helicoil for spark plugs

Jan 28, 2009 | 1990 Volvo 760

Not finding what you are looking for?
1995 Honda CBR 900 RR Fireblade Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...