Question about 2005 kawasaki KLX 110

Open Question

Installing kickstart shaft on 08 klx110. what position does the dog need to be in ? 10 o'clock ? 2 o'clock ? etc.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 298 Answers

SOURCE: my klx110 when kickstarting feels

A 110 bike never feels like it has compression try kinking a KTM 550.
It'll buck you in the air if it has a missfire!!.
Jokeing aside you have a stuck reed valve on this two cycle.
When you kick the bike in gear the clutch makes it feel like it has compression

Posted on Nov 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a yz125 and my kickstart will not engage what should I do? I have an electric start but it does not work and has been sitting till I had time to work on it can anyone help me


Hi, Runitdp305 and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty ignition switch.
6. Faulty starter button.
7. Faulty kickstand or clutch pull in switch/sensor.
8. Security alarm needs a reset.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
yz 125 wont start
Dirt Rider Magazine
can push down kickstart on yz125 with my hand is this normal Yamaha 2...
http://www.manualslib.com/manual/582255/Yamaha-Yz125-N-Lc.html

Jun 25, 2016 | Motorcycles

1 Answer

Remove kickstart on yz250f


Hi, Tyler for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Yz250f How to Replace Kick Shaft Help WR YZ 250F
Kickstarter on the 08 YZ250F
YAMAHA YZ250F Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Jun 07, 2012 | Yamaha YZ 250 F Motorcycles

1 Answer

1998 yamaha 125 kickstart will not retract back when i tighten down side cover


Hi, Masters for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Kickstart Won Come Back Up Help
YZ125 Part 10 2 Stroke Shifter Drum Kickstart Spring Gear ETC
YAMAHA YZ125 Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Oct 14, 2011 | 2003 Yamaha YZ 125

2 Answers

Need to change kick start spring


Hi, i am sorry but you dont say what the model of your machine is, this would help me determing the correct, answers for your questions, most kickstart springs can be changed by simply removing the clutch cover followed by the kickstarter shaft and then replacing the spring, make a note of kickstart stop location carefully remove the shaft holding the gears together replace the spring followed by the. Replacing the shaft and tensioning the spring before cover replacment, oil,etc. Some machines the shaft and spring is inside the centre cases and a complete engine strip is ness

Sep 25, 2011 | kawasaki KX 250 Motorcycles

1 Answer

I just replaced the kicker gear and what postion on the clock do i set the kicker at ????1973 bonnieville t140


http://www.triumphrat.net/attachments/classic-vintage-and-veteran/24674d1272815144-kickstart-stuck-78-bonneville-dsc00425.jpg

Notice the top most tooth is kind of aligned with the cover mounting bolt hole above it.

You want to be sure that the kickstarter gear does not engage the transmission shaft ratcheting gear when the kick starter lever is all the way up.

Aug 15, 2011 | Triumph Bonneville Motorcycles

1 Answer

I just bought an 1987 Yamaha TT350 dirtbike. is it a 2 cycle and how do i change the kickstart shaft


Hi, a yamaha TT350 actually has a 4 stroke engine. To replace the kick starter shaft, You need to remove the crankcase cover on the kick starter side of the engine..
The clutch basket etc will then have to be removed. '
You then use a set of needle nose pliers to unhook the kickstarter return spring from its post in the crankcase.
Release the return spring and allow it to relax. Then rotate the kickstarter assembly counterclockwise by hand , and remove the shaft assembly from the crankcase. Reverse this process to refit.
You can buy cheap workshop manuals for the yamaha XT/TT 350 models. Clymer manuals make them, there are usually good second hand ones on ebay etc,
the XT/TT350 workshop manual number is
M480-3.
These workshop manuals are a "must have" when working on bikes or cars etc, and by following a manual, at least you'll know that the job has been done safely and 100% correctly.

Apr 01, 2011 | Yamaha TT-R 250 Motorcycles

1 Answer

My 125dt dosent sart or kick sart,the gear inside have a bushing in shafting?or it was broken..


Common cause of kickstarter not engaging(I am guesing that this is your problem) is a broken spring on the kickstart mechanism,or that the kickstart idler gear cerclip has fallen off(this allows the idler gear to move forward on the shaft & thus won't allow the kickstart gear to transfer drive to the clutch hub).Remove clutch cover, put kickstart lever back on shaft spline,activate kickstart lever by hand(easier with sparkplug removed+in neautral)as kickstart lever moves down 90 degrees the gear on the kickstarter mechanism should move out to engage with gear next to it(kickstart idler gear).If the gear on the kickstarter mechanism dosn't move outward it has a broken spring on the kickstart mechanism.replace spring and all should work.(if the spring is broken you need to try find the broken piece with a magnetic pick-up tool as the broken part can cause further damage if not removed)To do this job I highly recommend you first purchase a workshop manual which will guide you through these processes.After all a manual is the most valuable tool in your tool kit.

Nov 17, 2009 | 2003 Yamaha YZ 125

1 Answer

Clutch wont engage after kickstarter shaft installation.


The clutch lever must have been pushed in when i tried to install the push rod the first time so the push rod didn't get pushed in all the way.

moz-screenshot.jpgmoz-screenshot-1.jpgmoz-screenshot-2.jpg
moz-screenshot-3.jpg7d3aefb.jpg

May 29, 2009 | 1996 Suzuki GSX-R 750 T

1 Answer

Netgear FR114P Time Checks


Most likely the router if you have the option turned on. Look at Schedule section of the configuration. Another possibility is Windows XP clients, assuming your clients are XP. The default installation has XP checking its time against time.nist.gov. Check the clock setting for this.

Feb 19, 2006 | NetGear FR114P Router

Not finding what you are looking for?
2005 kawasaki KLX 110 Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...