Question about 1979 Harley Davidson XLH 1000 Sportster

1 Answer

Adjustment on 1000cc values 1983 harley davidson sportster

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

To adjust the valves on your Ironhead Sportster, first collapse all the pushrod tubes, remove the spark plugs, and get the rear wheel off the ground. Put the transmission in fourth gear. Now, use the rear wheel to turn the engine.

To adjust the valves, bring the front cylinder to Top Dead Center. Use a common plastic drinking straw down in the spark plug hole to make sure the piston is at Top Center. Make sure both tappets for the front cylinder are all the way down. Now, loosen the lock nut slightly and turn the adjuster to make the tappet longer. You want to make it just long enough so that you can't turn it with your fingers. Gradually back down on the tappet until you can turn the pushrod with your fingers. Lock the locknut down when done. Now do the other tappet.

Once you've done the front cylinder, turn the engine using the rear wheel until the rear piston comes to Top Center. Always turn the engine in the normal direction of rotation. Adjust the two tappet the same way as you did the front cylinder tappets.

When finished, put the transmission in neutral, lower the rear wheel, put the plugs back in, and close up the pushrod tubes.

These tappets set to Zero Backlash, none. Therefore this must be done on a completely cold engine. When the engine starts up and as it warms up, the cylinders and head "grow" due to the heat expansion properties of the metal. As they grow, you pick up valve lash and the valves will clatter a bit. This is where the old saying came from, "You can tell it's a Harley from a mile away by the way the engine sounds. You can tell it's an Ironhead from a half mile away from the valve clatter". If you get the valves too tight, when the weather cools down in the winter, you could wind up with a valve standing open just enough to make the bike impossible to start due to low starting compression. It's better to have the valves a bit loose and have them clatter than have them too tight making the engine difficult to start.

Good Luck,
Steve

Posted on May 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know oil line routing for a 1984 ironhead sportster 1000cc


Hi, David sorry you can not find the first and best tool you ever bought for your Harley despair not, for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below, and for specific information or questions feel free to contact me at xlch@mail.com. Good luck and have a nice day.
oil line routing for 1984 ironhead sportster 1000cc Google Search
1979 ironhead oil lines
Harley Davidson Manuals Mark Workshop
http://www.stcharlesharleydavidson.com/OEMpartfinder.htm
Owner Manuals Harley Davidson USA
Instant Tech Relief A must have !!! only $6 a month "CHEAP"

Apr 10, 2016 | Motorcycles

1 Answer

I have a 1983 harley sporster ironhead that pops out of 2nd gear when down shifting. What needs to be replaced??


Hi Sam, and the usual suspects are:
1. Shifter rod improperly adjusted.
2. Shifter drum improperly spaced or damaged.
3. Shifter engaging parts badly worn and rounded.
4. Shifter forks bent.
5. Damaged gears.
Good luck and have nice day.

Apr 05, 2013 | Harley Davidson Motorcycles

1 Answer

Need to fix crankshaft for 1000cc harley davidson?


Hi Number32, should be someone at your local dealer or reputable shop that can handle that. Good luck

Aug 27, 2012 | 1979 Harley Davidson XLH 1000 Sportster

1 Answer

Change clutch cable on 74 sportster


Hi Anonymous, please tell me what is your question is and can you be specific and include details? Thank you and have nice day.

Jul 24, 2012 | Harley Davidson XLH 1000 Sportster...

1 Answer

1985 sportster 1000cc cylender torque specs


Hi Anonymous, in a criss cross pattern and your torque specs are:
1. 1/4" bolts 10 ft lbs.
2. 5/16" bolts 20 ft lbs.
3. 3/8" bolts 35 ft lbs.
4. 7/16" bolts 55 ft lbs.
5. 1/2" bolts 75 ft lbs.
Have nice day.

Jul 08, 2012 | 1979 Harley Davidson XLH 1000 Sportster

1 Answer

1979 Harley Davidson Cam Adjustment 1000CC


Hi Chris, for more information about your question please visit the website below. Good luck and have nice day.
picture of 1979 xlh 1000 cam timing marks Google Search

Oct 13, 2011 | 1979 Harley Davidson XLH 1000 Sportster

2 Answers

1979 Harley Davidson 1000CC Sportster Shovelhead cam set-up


Repair Manuals Online

The Internet, though, has a large number of web sites where you can buy service manuals and schematics from bookstores, publishers, and other collectors. Here is just a sampling of what sites are out there:

http://www.clymer.com/
http://www.haynes.com
https://www.howtomotorcyclerepair.com/


Oct 12, 2011 | 1979 Harley Davidson XLH 1000 Sportster

1 Answer

1980 harley davidson sportster 1000cc ironhead


Hi Jnoble2002, please tell me exactly what is your question is and can you be specific and include details like WHERE, WHEN , WHY, HOW? Thank you and have nice day.

Sep 15, 2010 | Harley Davidson XLH 1000 Sportster...

Not finding what you are looking for?
1979 Harley Davidson XLH 1000 Sportster Logo

1,419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...