Question about 1995 Yamaha XV 535 Virago DX

1 Answer

Change air filter

Small brass barrel 1 inch long came from somewhere, don't know where it goes

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

If you were changing your air filter you probably had to remove some bolts to take off the cover. The cover has brass spacers (barrels) so that when you tighten down the cover you do not crack the plastic. Take the cover you removed off and look you should see a bolt hole that is missing the spacer (replace it there.).

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

KenmoreElite790326333l5 lp convers., no instructions to change the oven broiler oriface. flame goes beyond reflector barrel + licks oven roof. Air adj. has no effect. Is this normal?


remove bottom drawer. right below the air adjustment part, you should see a brass colored nut. turn that nut till it tightens completely. then recheck. should be ok. be sure to put air adjustment opening like it was before.

Nov 26, 2015 | Kenmore Kitchen Ranges

1 Answer

Have a lose wire on a stihl 021 chainsaw by air filter but don,t know where it goes to


It probably goes to the ground on the choke lever. Remove the air filter and look at the area where the shut off switch is located, you should see a small slot where the wire slides in and connects with a metal piece in the stop position.

Apr 05, 2012 | Stihl Chain Saws, 017, 019, 021, 023 & 025

3 Answers

I have a Remington rifle which is a 22 caliber octagon barrel rolling block type serial number J282433. Any info on this rifle would be appreciated.


Could use more info, such as markings on the barrel and or breach. The Remington rolling block type single shot goes back to the 1860'S. The first 22 calibers around 1888. The rolling block went through 8 changes. The different types or changes are where various pins and screws are located, size and shape of hammers and triggers. The New Model Number 4, made from 1890 - 1933 came standard in 22 cal. with a 22 1/2 inch Oct. barrel. It will have a small lever on the right side of the breach. Approx 50,000 of these where made between the years noted. You could very well have a model 1, 2 or a model 7, which will be rare if in very good shape as only 1000, No. 7's where made. Tracking the serial number will be hard unless you contact Remington.

Oct 30, 2011 | Optics

2 Answers

My Weed Eater FL25 has rotted fuel lines. One is attached to the primer. Is the other the main? Is there a proper way to replace them? Diagram?


The brass fitting on the carb closest to the primer/purge bulb has a line on it that takes old fuel/air inside the carb and sends it TO the fuel tank. So it is routed straight to the tank. The lower brass fitting on the carb (side with vent hole in cover) has a line that goes directly to the fuel tank and has the in-tank fuel filter on it's end. To insert the main one that gets the filter on its end into the fuel tank, slice a notch out of the end of it so you can squeeze it into the hole in the tank. You can then twist and push it until enough of it goes in to grasp ahold of it with long tweezers or needle-nose pliars. Start off with about 1 foot of Tygon fuel line so you can do this. After you get ahold of it, pull it up thru the fill hole and attatch the filter. Then let it lay it the tank so it will move side to side on the bottom. With the extra line coming out of the tank (it seals the hole) see how much you need to reach the intake fitting on the carb (side with vent hole in cover). Cut it off and attatch it . The other line by the bulb only needs to enter the fuel tank about 1/2 inch or so and it also will seal the hole it goes through. You can notch it as well to help get it started into the fuel tank. This line will be short. I recommend you use NEW Tygon fuel line. I also recommend you get a new primer/purge bulb when you replace the fuel lines. It will deteriorate very soon, ask me how I know! They might have a fuel line kit with the filter, lines and bulb for your machine at Home Depot. Ebay has kits I know. Or you can go to the small engine repair shop and get exactly what you need.

Aug 07, 2011 | Garden

2 Answers

My rig is a 1991 Ford F250, auto, 4x4 with a 460 engine. I have a antifreeze leak somewhere above my oil filter. I think it is coming out of the silver box that my bottom radiator hose goes into... but I...


Is that silver box by chance the water pump? I would imagine the small hose is for the heater ... The big hose goes in, that's where it would draw in the water/coolant mix.

Jun 24, 2011 | Ford F-250 Cars & Trucks

2 Answers

Don't know how to get detergent into the ultimate x pressure washer (1500psi)


To the right of the Brass fitting where your garden hose attaches there is a small round plastic cover piece, pull on that and it will pull out a clear tube with it which goes into any container containing your detergent, it will pull the detergent as you use the pressure washer. Push the tube back in after you are done using it. You can also buy a replacement detergent bottle for other pressure washers if you wanted to.

Jun 05, 2011 | Garden

1 Answer

I am replacing the fuel lines on a Poulan 446 Pro Pole Saw. The two hoses inside the tank are completely dissolved away, so I don't know how much length to put in the tank. There is a 3/32 x 3/16...


Bill, the small hose connects to the fuel filter inside the tank feed the
hose thru the tank and pull out thru the filler hole and insert the fuel
filter, pull hose back to outside until you have 4" of hose in the tank
with the filter. this same hose connects to the bottom (shorter brass
stem to carburetor). the larger diameter hose will fit 1/4 " into the tank, and fit to the top (longer brass stem)

May 14, 2011 | Poulan Garden

1 Answer

I have a leaky faucet. I've shut the water off, removed the chrome cover over the control stem handle, but I'm stumped. How do you remove the brass fitting that holds the control assembly in place? I don't...


Normally there is an allen wrench that unscrews to allow the top to come off the control valve you can go to a home depot and show them the vavle repair you have to get the right allen wrench if you don't have the right one. normally they are 1/16 of an inch in diameter.there are three O-rings that can leak the barrel O-ring 2 of them and then the small o rigs for allowing the hot or cold to come out of with a spring on the inside of the barrel. let me know if you need more help.

Jul 04, 2010 | Hansgrohe 32020001 Talis S Single-Hole...

2 Answers

Poulan Weedeater sst25 25cc engine fuel line


ok If you have a Walbro WT series carb "without" a built on primer bulb here it is. First off if the fuel lines disintegrated you MUST disassemble it and clean it out. The MOST infintesimle speck of gas line trapped, can allow good prime and bad operation. OK? Don't be lazy on this. Just be delicate removing the flaps gasket and diaphram. ZAMA GND-12 Is the replacement Gasket and diaphram kit fot that carb. Use a cleaner, compressed air or blow good thru it. OK Now...Primer bulb, Carb, and Fuel tank, re connects: Smaller Diameter line comes from Gas tank (Connect filter screen to this in tank) to the short Straight brass carb connector. Primer bulb suction goes to the bent carb brass connector. If small line brings fuel "in" this other line sucks it back "Thru the primer bulb" and the blow side of the primer bulb sends it back to the fuel tank! So...Small Line brings fuel "TO/IN" carb thru short brass connect on carb. Other carb connect goes to bulb suction "IN", Then primer bulb "Pressure OUT" goes thru the larger tube "back to fuel tank". Trust me I know how frustrating a simple diagram is to find online fo this set up. And if you have a carb problem on top of the hook up uncertainty you got frustration. Not only was online help hard to find (Mfg...etc NFG at all!) My local repairshop in BBrook NJ could not tell me how!!! and thats no lie! Walbro has a "generic" carb diagram but no "hook up info" specifically. Poulan don't list it either. And these things routinly fall to pcs. all 3 of mine crumpled together on yr. 3 of use.

May 02, 2009 | Poulan 25cc 2-Cycle Gas Powered String...

2 Answers

I need a diagram showing fuel filter placement


try "autozone.com" or your local library for diagrams or step by step instructions

Mar 08, 2009 | 1984 Mercedes-Benz Mercedes Benz 300 Class

Not finding what you are looking for?
1995 Yamaha XV 535 Virago DX Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...