Question about 2008 Triumph Triumph Bonneville

1 Answer

How to reset diagnostic - 2008 Triumph Triumph Bonneville

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

The only way to do this is through a Triumph dealer at a cost of approx £40 or get a mac tools ET80 @ approx £79 which will read any engine management issues that you will have in the future and reset them as well, at the moment these are the only two solutions.
If you cant find a mac tools dealer then try mactools@hotmail.co.uk

Hope this helps

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Electra Glide reads do1clr?


Hi Manuel, if you have a 2003 or older Harley Davidson here is how you can access the Diagnostic Fault Codes through your speedometer.
The reset switch is used to change the odometer display between mileage and trip values and to reset the trip odometer. It is also used to identify the speedometer calibration and to enter the diagnostic mode, clear diagnostic codes and exit the diagnostic mode.
The Diagnostic Mode is entered by holding down the odometer reset button with the "off/run" switch in the run position, turn the ignition from OFF to ON and wait for the fuel pump to stop priming then let go of the reset button. The normal power-up sequence will occur and before entering the diagnostic mode diagnostic codes set during this power-up sequence will be stored as well. When in the diagnostic mode the odometer will display the first diagnostic code. When the trip switch is pressed again the next code will be shown. If the trip switch is pressed for more than 5 seconds at any time while in the diagnostic mode, the diagnostic code displayed will be erased.
There are 7 different diagnostic codes available:
d01 - Speed sensor power output shorted low
d02 - Speed sensor power output shorted high or open
d03 - Not Used
d04 - Not Used
d05 - Speed sensor return shorted high
d06 - Speed sensor return shorted low
d07 - Not Used
d08 - Speedometer power over voltage
d09 - Speed output shorted high
d10 - Speed output shorted low or open
CAL XX - Speedometer application calibration number:
14 = Domestic
15 = HDI
When in the diagnostic mode, all codes are displayed in sequence from d01 to d10.
As a code appears in the display (for instance d02), it will read
"d02Set" if set or "d02CLr" if clear.
You can exit the diagnostic mode by turning ignition from ON to OFF to ON again without depressing the reset switch or if a speed signal greater than 5 MPH is detected.
Diagnostics cannot be performed if system voltage is less than 9 VDC or greater than 16 VDC. The only exception is d08 which is set when system voltage is greater than 16 VDC.
After all the diagnostic codes are displayed, the speedometer
Calibration number is displayed example CAL 14 if you change rear wheel size or gearing you need to visit your local Dealership to have your speedometer recalibrated.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Harley Davidson FLHTCUI Ultra Classic Electra Glide 2002
Harley Davidson Touring Models Workshop Service Repair Manual 2002 $9 very cheap
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://www.harley-davidson.com/content/h-d/en_US/home/owners/maintain-your-bike/owners-manual.html
Instant Tech Relief To speak with me personally absolutely "FREE"

Apr 13, 2017 | 2002 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How do i reset the airbag light on a 2007 Cadillac STS


You need a diagnostic meter that has the air bag reset feature to do that. Most repair shops have have them. You may be able to borrow one from Auto Zone. You connect it to the diagnostic plug to reset it.

Nov 15, 2015 | Cadillac Cars & Trucks

1 Answer

How to reset oil light service


You'll need an inexpensive engine diagnostic meter that has a reset function. You connect it to the diagnostic connector on your car and press the reset button.

Aug 08, 2015 | Cars & Trucks

1 Answer

F13814978


Try this diagnostic cycle operation to reset.

To start the Service Diagnostics Cycle, press the
following keys, in order, in less than 6 seconds, while in standby(power on but unit off):
Heated Dry, Normal, Heated Dry, Normal
To Rapid advance one interval at a time, press the Start key, noting that
unlike Standard cycles, the Diagnostics Cycle automatically resumes
after door openings and does not require pressing Start to resume.

Once the diagnostic cycle has run and shut off, run a normal wash cycle, empty and with no detergent, to reset the control to factory "normal" operation. Make sure there's plenty of hot water.

Feb 14, 2014 | Whirlpool 24 in. GU3200XTP Built-in...

1 Answer

1999 Harley Davidson diagnostic codes


Hi Anonymous, if you have a 2003 or older Harley Davidson here is how you can access the Diagnostic Fault Codes through your speedometer.
The reset switch is used to change the odometer display between mileage and trip values and to reset the trip odometer. It is also used to identify the speedometer calibration and to enter the diagnostic mode, clear diagnostic codes and exit the diagnostic mode.
The Diagnostic Mode is entered by holding down the odometer reset button with the "off/run" switch in the run position, turn the ignition from OFF to ON and wait for the fuel pump to stop priming then let go of the reset button. The normal power-up sequence will occur and before entering the diagnostic mode diagnostic codes set during this power-up sequence will be stored as well. When in the diagnostic mode the odometer will display the first diagnostic code. When the trip switch is pressed again the next code will be shown. If the trip switch is pressed for more than 5 seconds at any time while in the diagnostic mode, the diagnostic code displayed will be erased.
There are 7 different diagnostic codes available:
d01 - Speed sensor power output shorted low
d02 - Speed sensor power output shorted high or open
d03 - Not Used
d04 - Not Used
d05 - Speed sensor return shorted high
d06 - Speed sensor return shorted low
d07 - Not Used
d08 - Speedometer power over voltage
d09 - Speed output shorted high
d10 - Speed output shorted low or open
CAL XX - Speedometer application calibration number:
14 = Domestic
15 = HDI
When in the diagnostic mode, all codes are displayed in sequence from d01 to d10.
As a code appears in the display (for instance d02), it will read
"d02Set" if set or "d02CLr" if clear.
You can exit the diagnostic mode by turning ignition from ON to OFF to ON again without depressing the reset switch or if a speed signal greater than 5 MPH is detected.
Diagnostics cannot be performed if system voltage is less than 9 VDC or greater than 16 VDC. The only exception is d08 which is set when system voltage is greater than 16 VDC.
After all the diagnostic codes are displayed, the speedometer
Calibration number is displayed example CAL 14 if you change rear wheel size or gearing you need to visit your local Dealership to have your speedometer recalibrated.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Does 1999 show diagnostic codes Harley Davidson Forums
Harley Davidson Manuals Mark Workshop
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://www.harley-davidson.com/content/h-d/en_US/home/owners/maintain-your-bike/owners-manual.html
Instant Tech Relief To speak with me personally absolutely "FREE"

Jan 19, 2014 | Harley Davidson Motorcycles

1 Answer

Can I reset my own engine service light?


the CPU which controls the operation of the light/s can be reset by the use of a code reader tool (Diagnostic tool)

Jan 14, 2014 | 1999 BMW 7 Series

1 Answer

How to reset engine light chevrolet traverse 2011


The check engine light arises when ECU finds any fault in the vehicle. Check for error code using On- Board Diagnostic system and then repair the codes.

Have a professional reset by on board diagnostic: You can tell any professional mechanic who have on board diagnostic system to reset the check engine light. The mechanic would not charge you with any penny.

If you do not want to try any of the above method then try hard resetting the check engine light; for hard resetting, follow the steps below:

1. Remove the battery terminals

2. Switch on the lights and press the horn for few minutes until last bit of electricity is drained.

3. When the horn stops working, you can now connect the battery again.

Jun 26, 2013 | Cars & Trucks

1 Answer

HOW DO YOU RESET THE SERVICE INTERVAL INDICATOR ON A 2006 DISCOVERY 3 TDV6


You can take it to a garage that can run diagnostics on your vehicle, as you need to plug in a laptop that has the diagnostic program on it and switch off the indicator. This also goes for engin mangement lights, airbag warning lights etc. As long as the garage has the correct diagnostic program they caan reset all the dash lights you want resetting. Hope this helps ;)

Apr 15, 2010 | 2006 Land Rover LR3

2 Answers

MY TROUBLE LIGHT IS STAYING ON


2000-2004

The Diagnostic Mode is entered by turning the ignition from OFF to ON while holding the reset switch in. The normal power-up sequence will occur before entering the diagnostic mode. Diagnostic codes set during this power-up sequence will be stored as well.

Important Note: Be sure no diagnostic codes are indicated before reset is held in for more than 5 seconds or diagnostic information will be lost.

When in diagnostic mode the odometer will display the first diagnostic code. When the trip switch is pressed again the next code will be shown. If the trip switch is pressed for more than 5 seconds at any time while in the diagnostic mode, the diagnostic code displayed will be erased.

There are 7 different diagnostic codes available. They are as follows:
d01 - Speed sensor power output shorted low
d02 - Speed sensor power output shorted high or open
d03 - Not Used
d04 - Not Used
d05 - Speed sensor return shorted high
d06 - Speed sensor return shorted low
d07 - Not Used
d08 - Speedometer power over voltage
d09 - Speed output shorted high
d10 - Speed output shorted low or open
CAL XX - Speedometer application calibration number:
14 = Domestic
15 = HDI


When in the diagnostic mode, all codes are displayed in sequence from d01 to d10.

As a code appears in the display (for instance d02), it will read "d02Set" if set or "d02CLr" if clear.

The diagnostic mode is exited either by turning ignition from ON to OFF to ON again without depressing the reset switch or if a speed signal greater than 5 MPH is detected.

Diagnostics cannot be performed if system voltage is less than 9 VDC or greater than 16 VDC. The only exception is d08 which is set when system voltage is greater than 16 VDC.

After all the diagnostic codes are displayed, the speedometer calibration number is displayed (CAL 14 for example).

Jun 12, 2009 | 2000 Harley Davidson FLTR-FLTRI Road Glide

3 Answers

Dishwasher Reset / Diagnostics


Unscrew and remove the kickplate at the very bottom of the dishwasher. The tech sheet with the diagnostic code should be attached to the back of it.  If not, due a websearch and you should be able to find the info on yahoo or google.

Jan 05, 2009 | KitchenAid 24 in. KUDS01FLBL Built-in...

Not finding what you are looking for?
2008 Triumph Triumph Bonneville Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...