Squeak at left rear wheel due too loose axle spindle nut. What is recommended torque setting for the spindle nut on 1990 corvette conv.

Help here in various sites. I presume you mean the rear wheel axle nut.

https://www.google.com/search?q=2005+Mazda+2.+Rear+drum+brake+spindle+nut+torque

..

36mm

2002 Chevrolet Suburban 1500 - Spindle And Axle Nuts

O'Reilly Auto Parts https://www.oreillyauto.com > cv--driveshaft---axle
Thread Size: M24-2.0 ; Hex Size (mm): 36mm.

Torque

https://www.google.com/search?q=2002+Chevy+Suburban+Z71.+axle+nut+torque

..

1995 C1500 spindle nut torque procedure? - CK5 Network

https://ck5.com > ... > General Discussion > The Garage
Jan 31, 2005 - while rotating the hub in a foward direction torque the nut to about 12ft lbs. Keep doing that a few times to ensure the bearings are seated.

96 gmc: torque..the front spindle nut..C1500 - JustAnswer

https://www.justanswer.com > Car Questions > GM Repair
Sept 16, 2011 - Torque nut (12) 10-12 ft lbs while turning the wheel assembly forward by hand. This will seat the bearing. Loosen nut (12) to a just loose ...
1 answer · Top answer: You can attach the magnetic base to the end of the spindle or to the brake caliper bracket. ...

• 
  

  1996 chevy: the torque setting for front wheel bearing..1500 4x4

  https://www.justanswer.com > chevy > 1tv6x-1996-che...
  Feb 18, 2009 - Outer Tie Rod Nut (C and K Models) · Shackle to Frame Nut and Bolt (C3500HD) · Shock Absorber Nuts (K Models) ; 62 N·m · 95 N·m · 90 N·m ; 46 lb ft.

Torque specification guide - PDF4PRO

https://pdf4pro.com > cdn > torque-specification-...
PDF
Front and rear axle nut torque specifications for FWD, RWD and 4 W/D vehicles. Torque specification guide. Form #457377. April, 2007.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

REMOVAL & INSTALLATION

1. Loosen the wheel nuts.
2. Carefully raise the locking tab of the axle spindle nut using a hammer and chisel.
3. Loosen and remove the axle nut.
4. Raise and safely support the vehicle.
5. Remove the rear wheel.
6. Remove the halfshafts from the differential. Refer to the differential removal procedure in this section for specific details.
7. Carefully remove the halfshaft from the trailing arm assembly by tapping on it with a plastic hammer, or using a suitable drift and hammer.

To install:

Installation is the reverse of removal taking note of the following points:


• Install new set rings in the groove of the splined inner CV-joint shafts.
• Top off the differential fluid as necessary.
• Install a new spindle nut and torque to 134 ft. lbs. (181 Nm), and once tightened, stake the nut.
• Tighten the wheel nuts to 80 ft. lbs. (108 Nm).

Remove the axle nut from the spindle, remve the spindle from the strut to allow room to remove the axle from the spindle, tap the axle out of the spindle. Once loose put a pry bar between the transmission and the axle and pry the axle out of the transmission. Might be a little hard to pry out but it will pop right out. Then to put the new one it just put it in, line it up and tap it in, be sure to torque your axle nut to the correct specifications when tightening or you will have a bad wheel bearing in no time.

is it independent suspension up front cv axles or halfshafts is how you tell i cant remeber on the 98 without looking it up but the best way is to get the chiltons so you have your torque spets to reinstall its not to dificult to do eather way but are you trying to replace the stearing nuckle or the wheel bearings? it eather has cv axles that go through a sealed one piece wheal bearings or it has a splined axle with u joints that go through a bearing hub on the rotertif thats the case the spindle has 6 nuts take them off you can get the special tool a sliding hammer to take it off i just use a dead blow if all else fails wont damage it make sure you check the inner neadle bearing for play. grease bolt back up torque down pack your bearings put in the new bearing seal. now you torqu the berings down with the nut to seat the bearings go back 1/4 of a tern you want 8 to 10 thousanhts of preload you can use a dial indicator to check yourself,set the locking washer and set the locking nut to torque remember when you do that your going to loose some of your preload about 1 to 2 thousenths

drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801cda30