Question about 1993 Harley Davidson XLH Sportster 883

1 Answer

Will the front wheel off of 2000 sportster fit 1995 sportster?

I would like to mount a 2000 model sportster on my 1995 sportster and would appeciate an answer letting me know if this is possible . thanks

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Hello, No a 2000-up Wheel has "Sealed Bearings" and the Lip around where the Disc Rotor Bolts is Larger (2.200") than the 1995 Wheel which has a Lip around where the Disc Rotor Bolts is 2.000". Also The width of the 2000-up Wheel will be a little Wider (about .200" = a little under 1/4"). The Wheels from 1984-1999 will be the Same for the Same Model of Harley. All Harley Wheels from 1973-1999 used 3/4" "Timken" Bearing (Tapered Caged Rollers), Wheels 2000-Up used "Sealed Bearings" 3/4" & 1" I.D. and in 2008 some started using 25mm Wheel Bearings. Anything is Possible if you Own a Machine Shop and want to Bore out your 1995 Disc Brake Rotor I.D. to 2.220" and Make New Axle Spacers and Machine off aprox. .100" off each side of the Hub. Thanks Bob @ Bob's Cycle Supply Since: 1976

Posted on May 01, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear wheel assembly on a 1995 sportster

Hi Anonymous, this is a statement not a question, I need more information please tell me the year and model of your bike and exactly what your question is and can you be specific and include details like WHERE, WHEN, WHICH ONE, HOW MUCH, so I can correctly address your problem. Thank you and have nice day.

Sep 01, 2013 | 2000 Harley Davidson XL 1200 C Sportster...

1 Answer

Front wheel hub diagram

What won't fit?
Too wide?
Too narrow?
Axle won't fit?

Jul 16, 2013 | Harley Davidson Motorcycles

1 Answer

Where is ignition module located on a 2000 hd sportster 883

Hi Anonymous, 1998 and later Sportster models circuit breaker and fuses were located in an electrical bracket behind the starter relay and data link that was mounted behind the left side panel. 1997 and earlier circuit breakers only no fuses were located under the seat and for a free wiring diagram please visit the website below and good luck.
Harley Davidson Wiring Diagrams and Schematics

Apr 12, 2012 | 2000 Harley Davidson XL Sportster 883

1 Answer

How do you remove the starter from 2000 blazer

raise the front of vehicle & support on jackstands.It will help to take off the (left wheel on2.2L models,right wheel on 4.3L models)Remove skid plate(if equipped)On 2.2 models remove front driveshaft.On some early models,it may be necessary to raise the engine/transmission with a floorjack an under the transmission and remove the transmission crossmember for access to the starter motor bolts.On models so equipped ,remove the starter heat shield.From under the vehicle, disconnect the solenoid wire and battery cables from the terminals on the solenoid.Remove the starter mounting bolts, and then remove starter motor (note location of shims)

Jul 19, 2010 | 2000 Chevrolet Blazer

1 Answer

How to put a seat together for a harley davidson xl 1200 sportster?

On a 2000 XL 1200 or 883 you would slide the seat through the seat strap and then locate the front of the seat on the tab at the frame and push the seat forward until the seat mount at the back of the seat lines up with the bolt hole on the fender and then screw the seat into place with a phillips screw driver.

Jun 06, 2010 | 2000 Harley Davidson XL 1200 C Sportster...

1 Answer

Wiil part #44554-03 fit a 2004XL1200custom?this is suppose to be a 19inch front wheel.the stock wheel is a 21inch.thank you

Could not find that specific part number in my catalog, but assuming it is a SuperGlide front wheel, yes it will. You may have to buy the model-specific wheel installation kit. But be advised, the new wheel will drop your front end a bit and the clearance to the front fender may look a bit weird. Most, but not all, front wheels from 2000 up to about 06?? will interchange with a spacer/axle swap. Make sure your brake rotor spacing is the same too. I know between 1999 and 2000 it was changed. Not sure if there were any running changes in between 2000 and 06.

Nov 11, 2009 | 2004 Harley Davidson XL 1200 C Sportster...

2 Answers

What year engines will fit in my 1996 ZX6 frame?

1995-1997 after this the mountings were changed

May 08, 2009 | kawasaki ZZR 600 Motorcycles

1 Answer

2000XLC Sportster front end vibration

Hard to diagnose, but if you have a bad engine vibration, you will be able to diagnose that when stopped and just revving up the engine. Moving balance problem can be easily out of true wheel and or needs balanced. (You can make your own balancer/ wheel true guage our of a couple of 8X8 posts with axle size hole drilled in each one) If you clonked a curb or pot hole at speed this can easily happen. Hope this helps you with your scoot, Rick

Apr 29, 2009 | 2000 Harley Davidson XL 1200 C Sportster...

1 Answer

Front wheel bearings

to remove the hub and bearing assy. you need to remove the tire and wheel, brakes, cv axle, then unbolt the lower ball joint, and remove the lower strut mounting bolts. I believe theirs two on this model after removing the hub & bearing assembly the hub must be removed by using a hydraulic press to press the hub from inside the bearing as they are a machined fit. then typically there is a large snap ring holding the bearing into its bore that needs to be removed before the bearing can be pressed out at the hydraulic press install is reverse of removal.

Sep 27, 2008 | 1995 Geo Prizm

Not finding what you are looking for?
1993 Harley Davidson XLH Sportster 883 Logo

959 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4752 Answers


Level 3 Expert

4348 Answers


Level 3 Expert

78267 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides