I've change my CDI it was faulty replace the coils and 4 plugs but my bike won't start

I have 2002 road star midnight. I lost completely spark on all 4 spark plugs. Before bike was running OK but sometimes on low RPM while idling would skip a firing on a at least one cylinder making spufff like sound. I put new spark plugs, and wiggled a little coil wires. Bike with new spurk plugs would not fire up at all. Checked for spark on all 4 spark plugs - no spark., not even an electrical I lost completely spark on all 4 spark plugs. Before bike was running OK but sometimes on low RPM while idling would skip a firing on a at least one cylinder making spufff like sound. I put new spark plugs, and wiggled a little coil wires. Bike with new spark plugs would not fire up at all. Checked for spark on all 4 spark plugs - no spark., not even an electrical charge going to spark plug. Went back to coils. Each coil (there 2 of them) has 2 spark plug wires and 2 ignition timing signal wires connected to them. I realized that these ignition timing wires contacts are corroded to the point they would not conduct a charge from the distributor to coil. CLEAN ALL THE TIMING WIRES Contacts on the coils. I did that and bike fired up right away and started running much better without sputtering or skipping a cylinder firing. SO DISCONNECT ALL THE COIL WIRES AND BRUSH THE CONTACTS WITH A SMALL METAL WIRE BRUSH.

you will have to check lead to spark plug then lead to coil
if your not getting spark at plug it could be a number of things ingintion
or just a loose wire best of luck hope you solve it

Sorry but they either work or they dont.
If yours isn't working, replace it.
But before you replce it consider checking the other components, because ign mods are exspensive.
it sounds like you've been already checking the other stuff. heres what i'd check if your bike came to my shop.
1. battery fully charged, and can take a load. (weak batteries = weak ign power)
i have a bike that won't fire at all with weak battery. Make sure battery is good.
2. check for spark at plugs, make sure plugs are good. Pull plugs and turn motor over.
rest plug next to head and turn over, do not touch the plug while turning over
or you can be shocked.look for spark.
if you have spark , then you ign mod is working.
if no spark, then check #3
3. power to coils. check the power going into coils,
if power but no spark, then coil is bad.
if no power. check #4
4. power to coils comes from a ignition system ( points/ cdi /ign. module)
there is a stator and a rotor. and a signal generator. on your motor
the signal generator wire sends a signal to the cdi, every time the rotor rotates.
the ignition system (ign.mod) sends power to coil.
so if no signal to the cdi, then signal generator is bad
if signal going into cdi but not sending the power to the coils then the cdi/ ign. mod is bad.

Hope that helps
Best Regards
Big Al

If you are able to use a digital volt meter and work your backwards from spark plug wire to coil to cdi to stator you can figure out where voltage stops.thats a fairly newer bike unless you really submerged that bike under water i dont think its the cdi box.it could be coil wire it could be coil.you want to check or change the cheaper parts before you go right to cdi because there not cheap.I have a yamaha banshee 350 and she was breaking up real bad.I thought because it was only happining on top end that the cdi was breaking down or stator was going bad.Found out with meter it was the coil wires and spark plug boots.These items have to have a certain amount of resistance or the do not conduct correctly.And spark plug wires and boots are not that exspensive.So thats why I say start from sparkplug boot and work your way back.Try that and Good Luck.

The decompression valve has come apart in the engine. Tear it down!