Question about 1972 Triumph T 100 R

1 Answer

Exhaust stub removoval - 1972 Triumph T 100 R

Posted by on

  • Geoff watson May 11, 2010

    are you refering to the exhaust flange fixing studs

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 233 Answers

The only way I could get them out is to heat them with a torch to glowing red and carefully tap on them on the end with a hammer, used a set of channel locks to remove while still hot... (try at your own risk...) hope this helps!

Dan

Posted on Mar 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I look for my employee pay stub account?


How to view pay stubs?
Wave
  1. In Personal click Payroll on the left side of your screen.
  2. Click Pay Stubs from the drop-down.
  3. Click the eye icon next to the pay period you'd like to view and download.
  4. Click PDF Version on the right to download a PDF of your pay stub.

How to view, download and print your pay stubs - Help Center

https://support.waveapps.com/.../208621916-How-to-view-download-and-print-your-pa...
How can look for my employee pay stub account Google Search

Oct 30, 2017 | Computers & Internet

1 Answer

How do you replace the rack and opinion on a 92 cutlass ceira


Here you are - power rack & pinion.

Except 2.2L and 1993-96 3.1L Engines
See Figure 1
  1. Raise the intermediate shaft seal and remove intermediate shaft-to-stub shaft pinch bolt.
  2. Remove the air cleaner and disconnect the pressure hoses from the steering gear.
  3. Raise and support the vehicle on jackstands, then remove both front wheel and tire assemblies.
  4. Remove the cotter pins and nuts from both tie rod ends. Using tool J-6627 or BT-7101, press the tie rod ends from the steering knuckle.
  5. If equipped with an Air Management pipe, remove the bracket bolt from the crossmember.
  6. Remove the 2 rear cradle mounting bolts and lower the rear of the cradle about 4-5 in. (102-127mm).

WARNING
If the rear of the cradle is lowered too far, the engine components nearest the cowl may be damaged.
  1. If equipped, remove the rack and pinion heat shield.



Fig. Fig. 1: Power rack and pinion assembly
  1. Remove the rack and pinion mounting bolts, then the gear assembly through the left wheel opening.
To install:
  1. Install the gear assembly through the left wheel opening and install the mounting bolts.
  2. Install the heat shield.
  3. Raise the rear of the cradle and install the mounting bolts.
  4. Install the bracket bolt to the crossmember under the air management pipe.
  5. Install the tie rod ends to the steering knuckles, install the retaining nuts and insert new cotter pins.
  6. Install the front wheels and lower the vehicle.
  7. Install the high pressure hoses to the steering gear and install the air cleaner.
  8. Install the intermediate shaft seal and the intermediate shaft-to-stub shaft pinch bolt.
2.2L Engine
  1. Disconnect the negative battery cable.
  2. Install an engine support fixture J-28467-A, or the equivalent.
  3. Raise and safely support the vehicle.
  4. Remove the tire and wheel assembly.
  5. Remove the intermediate shaft lower pinch bolt.
  6. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.
  1. Remove the exhaust pipe hanger bracket near rear of frame including the brake line retainer and rubber exhaust pipe hangers.
  2. Remove the engine and transaxle mount nuts at the subframe.
  3. Support the rear of the subframe with jack stands.
  4. Remove the rear subframe bolts and discard.
  5. Lower the subframe for access to rack and pinion.
Do not lower the rear of the cradle too far, as damage to engine components nearest the cowl may result.
  1. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
  2. Disconnect the power steering lines from the steering gear.
  3. Remove the rack and pinion mounting bolts and nuts.
  4. Remove the rack and pinion through left wheel opening.
To Install:
  1. Install the rack and pinion through left wheel opening.
  2. Install the rack and pinion mounting bolts and nuts and tighten to 66 ft. lbs. (90 Nm).
  3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm) on the pressure line.
  4. Install the power steering line clip to steering gear.
  5. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
  6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
  7. Remove the jack.
  8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
  9. Install the exhaust pipe hanger bracket near the rear of frame including brake line retainer and rubber exhaust pipe hanger.
  10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
  11. Install the tire and wheel assembly.
  12. Lower the vehicle.
  13. Remove the support fixture.
  14. Connect the negative battery cable.
  15. Refill the power steering reservoir and bleed the system.
  16. Check the front end alignment and adjust as necessary.
3.1L Engine (VIN M)
  1. Disconnect the negative battery cable.
  2. Remove engine torque strut from engine.
  3. Install an engine support fixture J-28467-A, or the equivalent.
  4. Raise and safely support the vehicle.
  5. Remove the tire and wheel assembly.
  6. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
  7. Remove the center engine and rear transaxle mounts from the frame.
  8. Remove the intermediate shaft lower pinch bolt.
  9. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.
  1. Remove the brace bolts and brace, including brake line brace.
  2. Support the rear of the subframe with jack stands.
  3. Remove the rear subframe bolts and discard.
  4. Lower the subframe for access to rack and pinion.
  5. Remove the steering gear heat shield.
  6. Remove the clip holding lines at rack assembly.
  7. Disconnect the power steering lines and O-rings.
  8. Remove the rack and pinion mounting bolts and nuts.
  9. Remove the rack and pinion unit through the left wheel well.
To Install:
  1. Install the rack and pinion through left wheel opening.
  2. Install the rack and pinion mounting bolts and nuts and tighten the mounting bolts to 66 ft. lbs. (90 Nm).
  3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm). on the pressure line.
  4. Install the power steering line clip to steering gear.
  5. Install the steering gear heat shield.
  6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
  7. Remove the jack.
  8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
  9. Install the brace and bolts including brake line brace.
  10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
  11. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
  12. Install the tire and wheel assembly.
  13. Lower the vehicle.
  14. Remove the support fixture.
  15. Connect the negative battery cable.
  16. Refill the power steering reservoir and bleed the system.
  17. Check the front end alignment and adjust as necessary.

25936701-ge4w2xkagkibehwv23tkbbb2-2-0.gif

Nov 01, 2015 | Cars & Trucks

1 Answer

Why is the water running out of my water heater slowly?


If you take your pipe off the hot side of the water heater, there is a check valve in the pipe that is stubbed up. They vary in style, usually it is like a marble and it gets stuck. It is easier to replace the stub with a brass nipple and put the dielectric fitting back on it.

Dec 19, 2014 | Fasco Bradford White Hot Water Heater...

1 Answer

How to get my pay stub


To obtain a copy of your pay stubs you need to contact an HR (Human Resources) rep where you work. You can often do that on-line.
You are entitled to get pay stubs; if you have any problem come back here

May 05, 2014 | Computers & Internet

1 Answer

How do i get the axle stub out of the transaxle of my 97 vw jetta


drive out cv joint out of transmission using a hammer and brass punch.

Sep 25, 2012 | 1997 Volkswagen Jetta

1 Answer

I scan parking stubs and it splits them up into multiple pictures when I save it to the PC. I want all stubs to fit on 1- 8.5x11 and save to PC.


1. Scan the first parking stub then click on File - Save the image as a jpg file Eg. image1.jpg

2. Repeat the scan the next parking stub and save the image file Eg. image2.jpg

3. Repeat step 3 for the other
parking stubs.

4. Close the scanner when finished scaning.

5. Open a Word document then place each parking stub image file on the page. You may need to resize each image to fit them all on the page or you may wish to place the images over a few pages.

6. Save the Word document.

Jul 09, 2011 | Canon PIXMA MP830 All-In-One InkJet...

1 Answer

Front axle removal


remove the axle stub retaining nut, disconnect the lower ball joint, disconnect the tie rod end, pull the spindle out and away from the axle stub tapping on the end of the stub if necessary with a hammer (just be careful) to pull the bearing hub loose from the axle stub. after separating the outside slide under vehicle (make sure the car is on jack stands and the rear wheels are blocked from rolling and very secure before crawling under any vehicle) look at where the inside axle stub goes into the transmission. you'll need a good sized pry bar to pop the axle out of the transmission. work the pry bar in between the inside axle stub and a good thick part of the transmission and pry the axle away from the trans., there is a snap ring on the inside axle stub that internally retains the axle you have to pry hard enough to compress the snap ring into the axle groove which will release the axle for removal. it's not a bad idea to replace the axle seal in the transmission while you're there but if it's not leaking and you don't damage it in the removal of the axle it's not necessary. measure and compare the new axle to the old one, it may have some differences in the shaft like missing vibration dampeners but if it's the same length and both axle stubs match the old ones in size and number of teeth you should be good. when you install the new axle line it up by hand and slide it in as far as possible manually then tap it in with a wooden or rubber mallet. if you don't have a mallet use a scrap of wood to protect the new axle stub threads and tap it in with a hammer. after you feel the snap ring collapse and the axle slide in tap on it gently to make sure it's fully seated then grab the inner axle stub and tug on it to insure the snap ring is in place. then reassemble in reverse order of removal making sure all nuts and bolts are tightened properly and all retainers are in place. good luck

Jan 06, 2011 | 1997 Chrysler Concorde

1 Answer

Doesn't heat up but fan and light still work


If the fan is working o/k then you you need to replace the main oven element, located at the rear of the oven behind removovable cover.
Please rate my solution.
Thanks.

Oct 25, 2009 | Whirlpool Ovens

1 Answer

2001 yz125 exhaust


if you have any friends that weld. ive had this problem myself and have found it cheaper and less stressful to fabricate yourself than to search any further

May 10, 2009 | 2003 Yamaha YZ 125

1 Answer

How to take a stub shaft off a 1984 turbo -350 transsmission


stub shaft is affixed from inside the transmission

May 19, 2008 | 1983 Chevrolet Silverado

Not finding what you are looking for?
1972 Triumph T 100 R Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...