Question about 2004 Honda CR 125 R

1 Answer

1990 cr 125 did the top end reassembled,all i did was un hook the linkage on the power valve i cleaned the assembly and put i back together,how do i know if it is right..

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 617 Answers

Look thru exhaust port turn the valve should see port open up

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1988 yamaha blaster and the carb has been cleaned several times but now when I put the carb back in and then hooked up the fuel line the carb started leaking out the overflow hose. An so I cannot...


It sounds like the float got stuck in the open position when you went to reassemble the carburator, thus allowing fuel to flow constantly. With the handle end of a screw driver try tapping the bowl a few times. This may free it up, but If the leaking doesn't stop your going to need to take it apart again and check the float assembly again.

Jan 04, 2011 | 2003 Yamaha YZ 125

1 Answer

I have a 1998 cr 125 i just bought it and when i rode it it didnt seem like it had any power no low end and it took forever to get it up to speed i put new reeds in it but that didnt help so i took the...


120 psi means you need top end( should be around 160psi) if you can feel the score marks with your finger you will have to have the cylinder bored and install a over-sized piston kit,if you cant feel them than you can have it honed.....now the stuck power valve is why you didn't have any power,take them out and clean all the carbon deposits off them and reinstall, pay close attention to how they come out so you can put them back the same way...if you have a manual you can check the adjustment specs on them also.....now on to the crank,the first indication of bad crank seals or bearings is losing your trany fluid,if you don't feel any unusual vibration or hear any unusual whining or have a large amount of lost trany fluid your probably OK with the crank.......yz-maniac

Jul 03, 2010 | 2002 Honda CR 125 R

1 Answer

1991 buick regal, i need instructions on how to replace a ignition switch


key switch,remove center cap and pull steering wheel off with wheel puller.disconect horn,blinkers assembly.push pin remove ignition. ignition switch, remove panel under dash un bolt steering colum lower to seat un screw ignition from top steering colum un hook rod,un plug harnees put new one on put back together

Feb 02, 2010 | Buick Regal Cars & Trucks

2 Answers

1990 vulcan 750 throttle


no spring in the grip!
id suspect the cables are binding up inside so disconnect at the carby end then & see if they are moving freely
Cheers Rob

Aug 16, 2009 | 1990 kawasaki VN 750 Vulcan

2 Answers

Yamaha 125 grizzly starts and idles when choked but dies when acc


check that reed valves not sticking and check the pilot jet its prob. half blocked. have to stick a very thin wire through it.

Aug 12, 2009 | 2003 Yamaha YZ 125

1 Answer

How do you tell if the power valve is working on a 1990 rm 125. it is real doggy on the top end.


If the bike does not bog out on the bottom end then the power valve is working. Try cleaning the carb and be sure gas flows freely past the float needle.

Aug 02, 2009 | Suzuki RM 125 Motorcycles

1 Answer

98 cr 125 has spark and gas but wont start.


When you rebuil the top end and pulled the power valve off did you put the screws bacvk in to the valve arm before puting the case and top end on cause you will either be closed or wide open on valve.and did you put the reeds back in? and make sure the floats are right and all jets are back in it the right way. try that

Jul 04, 2009 | 2002 Honda CR 125 R

1 Answer

2004 Honda CR 125 R adjust power valve


Hi, Snookerdude for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Cr125 power valve setup Linkage arm
ASK THE MXPERTS HOW DO YOU ADJUST HONDA ELECTRIC POWER VALVE ON THE OLD...
Honda CR 125R 2002 Sevice Manual
http://www.partsfish.com/page/oem-parts-for-honda
http://owners.honda.com/assets/OWNERLINK/model/own_man/powersports/2007/2007_CR125r.pdf

Jun 05, 2009 | 2004 Honda CR 125 R

1 Answer

Trouble with speed.


Yes. The application of a proper pipe on a two-stroke motor is critical. The 250 pipe has way to much volume and not enough back pressure to allow the 125 motor to breath properly.Also check the ignition timing carb jetting and power valve for proper working order per Honda specifications.,

Nov 10, 2008 | 2007 HM CR 125R

Not finding what you are looking for?
2004 Honda CR 125 R Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...