Question about 2008 Harley Davidson FLHX Street Glide

1 Answer

In what order do the wires go into the deautsch

In what order do the wires go into the deautsch connector from the trottle sensor there is 2 sets of wires coming out of the trottle sensor 1 yellow group and 1 black group bothe have 1 red 1 black and 1 white wire the back of the connector is numbers 1-6 in what order do the wires go

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 109 Answers

Isn't it fail safe? I mean yellow group red wire will only go in lets say 3 if you try any other # it won't go.Just a thought,have you tried that?

Posted on Mar 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I cant seem to fine the trottle posion sensor on my 1994gmc3500


https://s14.postimg.org/dcdabvn0h/tps.jpg

It's on the throttle-body, probably opposite side from throttle cable and lever.
Click on the link, you can see three wire connector and you can see wire colors.

Jun 11, 2017 | Cars & Trucks

2 Answers

How many o2 sensors a Cadillac Deville 2000 has. I find 3 and replace them but still I have P0155 code for B2S1? Need help!


Which engine ? Some have four and always double check the connections as they can set the codes .

Mar 01, 2016 | Cadillac Cars & Trucks

1 Answer

Co222 '03 Trailblazer


C0222 and C0226 The corresponding wheel speed sensor signal is less than 6 km/h (4 mph) for 5 seconds, or 120 seconds in order to set both DTCs.
Did you perform the ABS Diagnostic System Check?
--
Go to Step 2
Go to Diagnostic System Check - ABS

2

  1. Use a scan tool in order to clear the DTCs.
  2. Operate the vehicle at a speed greater than the specified value.
Does the DTC set?
19 km/h (12 mph)
Go to Step 3
Go to Diagnostic Aids

3
  1. Turn OFF the ignition.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Disconnect the wheel speed sensor connector.
  4. Use a DMM in order to measure the resistance across the wheel speed sensor.
Does the resistance measure within the specified range?
700-10,000 ohms
  1. Spin the wheel by hand as fast as possible.
  2. Use a DMM in order to measure the AC voltage across the wheel speed sensor as the wheel spins.
Does the AC voltage measure greater than the specified value?
100 mV
Go to Step 5 yes
Go to Step 8 no

8

Replace the wheel speed sensor. Refer to Wheel Speed Sensor Replacement .
Did you complete the replacement?

5

Inspect for poor connections at the harness connector of the wheel speed sensor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 10
Go to Step 6

Aug 11, 2015 | Cars & Trucks

1 Answer

No power,02 spectra has 0 power had it scanned said it need a throttle poss sencer replaced with a new one still no power,has fuel pressure driving me nuts what could this be


THERE IS ISSUES WITH THE TROTTLE POSITON SENSOR THERE IS ALSO A ECM SOFTWARE UPGRADE ALSO I WOULD CHECK THE WIRING RIGHT OFF THE CONNECTOR THE WIRE TENDS TO BREAK INSIDE THE INSULATION GO BEHIND THE CONNECTOR AND PEEL BACK WIRE PROTECTOR ABOUT 3 INCHES AND GRAB THE WIRE AND INSPECT YOU WILL NEED TO FEEL FOR IT CAUSE NORMALLY YOU CANT SEE THE BREAK THROUGH THE INSULATION SEEN ALL OF THESE ISSUES MANY TIMES

Jan 15, 2011 | 2002 Kia Spectra

1 Answer

1990 buick lasabre with a 3.8 engine, cranks but no spark. No voltage to the primary side of coil. Code shows 22. Changed the trottle position sensor, crank position sensor and cam position sensor. Had the...


1. Monitor the 5v reference, Gray wire to the Throttle Position Sensor (TPS) with a Digital Volt Ohm Meter (DVOM) set to the MIN/MAX setting.

2. Monitor the TPS signal circuit, Blue wire with a DVOM. Voltage should range smoothly from approximately 0.44 to 5.0 volts as the throttle is opened.

3. Tap test the Electronic Control Module (ECM) and see if the codes come back or if the engine reacts.

possible causes wiring or Powertrain Control Module (PCM)

Oct 31, 2010 | 1990 Buick LeSabre

1 Answer

Westinghouse LF708C fault code SE. not spinning. what needs to be fixed?


SE refers to a sensor error, remedies include checking all connections plugs: § The connector (5pin, male, white) in the Wire Harness is not connected to the connector (5 pin, female) of Hall Sensor in the MOTOR. ?_? reconnect or repair the contact in the connector The electric contact between the connectors (5 pin, male in the Wire Harness and 5 pin female in the Hall Sensor) is bad or unstable. ?_ Reconnect or repair the contact in the connector ? The connector (6 pin, male, natural) in the Wire Harness is not connected to the connector (6 pin, female, natural) of PWB ASSY(Main) or the electric contact of connectors is bad/unstable. ?_ Reconnect or repair the contact in the connector ? The electric contact between the connectors ¡a6 pin, male in the Wire Harness and 6 pin female in the controller(Main)¡bis bad or unstable. ?_ Reconnect or repair the contact in the connector ? The Wire Harness between Hall Sensor in the MOTOR and PWB ASSY(Main) is cut(open circuited). ?_ Repair/replace the damaged WIRE HARNESS ? The Hall Sensor is out of order/defective. ?_ Replace the Motor ? The controller(Main) is out of order/defective. ?_ Replace the PWB ASSY(Main)

Jan 22, 2010 | Westinghouse Washing Machines

1 Answer

IT IS NOT WORKING


Run this diagnostic
Test Procedures 
1. Check if DTC P0110 is set in addition to DTC P0105 or P0106. If DTC P0110 is set, go to next 
step. If DTC P0110 is not set, go to step 3 . 
2. Turn ignition off. Disconnect MAP sensor 4-pin connector. Measure resistance between ground 
and MAP sensor connector terminal No. 4 (Green wire). If resistance is one ohm or less, replace 
MAP sensor. If resistance is more than one ohm, repair open in Green wire between MAP sensor 
and ECM connector terminal No. 48. After repairs, clear DTC and verify MAP sensor operation. 
3. Turn ignition off. Disconnect MAP sensor 4-pin connector. Measure resistance between MAP 
sensor connector terminals No. 1 and 4 (component side). Resistance should be about 30,000 
ohms. If resistance is as specified, go to next step. If resistance is not as specified, replace MAP 
sensor. After repairs, clear DTC and verify MAP sensor operation. 
4. Turn ignition on. Measure voltage between ground and MAP sensor connector terminal No. 2 
(Red wire). Voltage should be about 5 volts. If voltage is as specified, go to next step. If voltage is 
not as specified, repair open in Red wire between ECM connector terminal no. 44 and MAP 
sensor connector terminal No. 2. After repairs, clear DTC and verify MAP sensor operation. 
5. Turn ignition off. Disconnect ECM 63-pin connector. Check for continuity between ground and 
MAP sensor connector terminal No. 1 (Green wire). If continuity does not exist, go to next step. If 
continuity exists, repair short to ground in Green wire between MAP sensor and ECM. After 
repairs, clear DTC and verify MAP sensor operation. 
6. Reconnect MAP sensor connector and ECM connector. Turn ignition on. Backprobe MAP sensor 
connector and measure voltage between ground and MAP sensor connector terminal No. 1 (Green 
wire). Voltage should be 0.2-4.5 volts. If voltage is as specified, go to next step. If voltage is not 
as specified, replace MAP sensor. After repairs, clear DTC and verify MAP sensor operation. 
7. Check ECM connector for loose or damaged terminals. If problem exists, repair ECM connector. 
If problem does not exist, replace MAP. Clear DTC and verify system operation. If problem still 
exists, replace ECM. After repairs, clear DTC and verify system operation.

Good luck and hope this helps. If the car does not start diconnect the MAP sensor to get you to the parts store if you need it to get you there.

May 25, 2009 | 2001 Hyundai Elantra

1 Answer

Diagnostic codes


P1226 Control Sleeve Sensor Malfunction
P1126 Throttle Position (Narrow Range) Sensor Circuit Malfunction
P1125 Throttle position sensor intermittent
I would say u are safe to assume the trottle sensor is defective or the wiring to the sensor is open or shorted. check the connector for pushed out pins.

Apr 22, 2009 | 2002 Mini Cooper

1 Answer

2001 ford taurus will not idle down


several things can do this but most likely would be
1 TPS trottle postion sensor = replace
2 stuck butterfly valve inside the trottle body = clean out with trottle body cleaner try to get most of the black build up with a old tooth brush
3 bad trottle cable= feel the cable make sure it moves freely if not replace it

Feb 20, 2009 | 2000 Ford Focus

1 Answer

Misfiring when accelerating at highway speeds in fifth gear


It could be a couple of things.
1) Check to make sure the wires are in the correct firing order.
2) Check to make sure th plugs are still good, including the gap.
If these don't work than you should probably have a mechanic look at it in person.

Jan 23, 2009 | 2007 Mazda B4000

Not finding what you are looking for?
2008 Harley Davidson FLHX Street Glide Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...