Question about 2004 Yamaha WR 450 F

1 Answer

Assembling hot start plunger,spring,seal...

Hot start plunger cap broke, it came out in pieces. How does hot start assembly go together? Looked at schematic but it is a little vague.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

Ok the phish is ez to read if you know what it is that you looking at so lets see if we can get this thing running. on the link i sent you we'll need to look at the numbers cause that is what i'm going to refer to. if you lay your parts out so you can see them it'll help as well.
http://fiche.worldofpowersports.com/wps/Yamaha_OEM/YamahaDB.asp?Type=13&A=347&B=11the
the cable is going to go into # 41 then 39 after that put the spring #38 over cable then hook on plunger #37
I hope this helps out please feel free to contact me if you need any more help
Mark
C.C Motorsports

Posted on Feb 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was cleaning my cr250r carburetor and in the process of putting it back together the choke broke and I can't get the plastic end out of the carb so I can replace it. Do I have to replace the whole t


looks like you broke the enrichner plunger and needle off in carb body, you should be able to get it out with a little finesse, the assembly is replaceable. try a set of small needle nose pliers or some picks, just try not to damage the carb body. you can see a diagram of the carb and parts for this at BikeBandit.com. they even have the new part for like $46.73. hope it works

Dec 18, 2012 | Motorcycles

1 Answer

How to take a part a model 31 shotgun schematic to show how to take it apart


Make 100% sure it is unloaded before you start. Open the action a little bit, then unscrew the barrel nut until you can see space between the plunger and the detent. Turn the barrel and magazine assembly 90 degrees and pull it out (yes, the 31 is a takedown gun). Push out the big pin in the receiver from right to left (looking down on the gun from firing position). Turn the gun upside down. Push the trigger assembly toward the front of the gun until it aligns with the slots, and pull the trigger assembly out of the gun. For BASIC disassembly, most users should stop here. The slide/bolt assembly is a little more complicated, and unless you have some patience, experience, or mechanical knowhow, getting them back together can be a little frustrating. For those who want to go farther, look up a copy of "The NRA guide to Firearms Assembly," or find a M31 manual on E-bay for under $10.



Read more: http://wiki.answers.com/Q/How_do_you_disassemble_a_model_31_Remington_shotgun#ixzz176Xpe7hJ

Dec 04, 2010 | Computers & Internet

1 Answer

How do I quilt on my 9000


Your question is a little vague... Put simply, here is how to make a quilt. Start by putting 2 pieces of material (good sides together) and sew a 1/4 inch seam. Keep on adding pieces until you have a quilt.

Apr 07, 2010 | Janome Memory Craft 9000 Computerized...

1 Answer

We just purchased a whirlpool dishwasher & while taking it out of the box I noticed a gray piece in the lower back with a red electrical part in the middle with a wire connected hanging down. I looked...


You just got it. call for service or take it back for a replacement. If that piece was damaged, what else was jarred and soon to fail. I would return it for a replacement.
Eric

Jun 28, 2009 | Whirlpool GU2700XTSB / GU2700XTSQ /...

1 Answer

Braun electric water heater lid came off along with spring parts, all intact. How do I re-assemble it? Manual? Schematic available?


This is the solution for the BLACK Braun electic water heater, so you must adjust the color to fit if yours is another color.
First take the 3 pieces that go inside the top. Two look like a "Z", and the other is the square, white doo-dad. Take the square piece and slip it into the slot with lid open. YOU CANT PUT IT IN FLAT UNLESS THE LID IS OPEN! Make sure that you can put it in FLAT. Once it is in flat, take it back out. Now you have the 2 "Z" pieces. Fiddle around with these pieces until you learn how to put them in together so they will fit together. This may take several tries. There is a piece that acts like a pivot. Now take all 3 pieces out. The trick is not to put the 2 "Z" pieces in together. You have to figure out what Z-piece to put in first. Then put the rectangular white piece in, and then the other Z-piece. This all must be done with the lid OPEN, otherwise the rectangular piece will not lie flat. Make sure the little spring inside this rectangular piece it put in properly - it should be against the little black doo-dad on the lid. If everything is sitting happily together, you should be able to snap the other black part onto the lid, and close it successfully.

May 16, 2009 | Braun WK200 AquaExpress Electric Water...

2 Answers

Won't dispense cleaning solution


I had this same problem. There is a solution posted elsewhere on this website. Search for Hoover Floormate H3000.

The following solution is the one I tried: Remove the fluid dispensing tank and put a small dab of hot glue on the tip of the blue/greyish "plunger" piece that is located in the middle of the black rubber circle. Let the hot glue dry (this forms an extension to the plunger piece...) and replace the fluid tank.

I did this and my machine is working properly again! Whoever posted this solution was very helpful!

Aug 24, 2008 | Hoover Floormate H3000 Upright Wet/Dry...

1 Answer

Cleaning solution drains out !!


There is a plunger and a seal on the bottom of the soap dispenser. It may be that the plunger is stuck. You may have to replace it part number SmartMix® Cap Assembly 2101795

Sep 14, 2007 | Bissell 1699 ProHeat Clear View Upright...

14 Answers

Not spraying liquid.


This is where you attach the Lego.

not-spraying-liquid-pi02cr1kttkrastpy2vlmywc-3-1.jpg

Nov 13, 2006 | Hoover Floormate H3000 Upright Wet/Dry...

Not finding what you are looking for?
2004 Yamaha WR 450 F Logo

Related Topics:

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

vince

Level 3 Expert

652 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...